Past Radiation Monitoring & Comments
SW Oregon Radiation Monitoring for the Coos Bay & North Bend area
(See also: current/recent monitoring)

See Space Weather for current solar/storm news. Energy News (check beyond their often lurid headlines) has slacked off in 2016.
We can follow the demise and poisonous death throws of the nuclear industry via Ring of Fire, Common Dreams, Truthdig and others.

You're at: https://57296.neocities.org/rad-2.htm

Contents
Last worked on: May 16th, 2024
fast find>> Preamble, Air sampling, Air update, Solar flares, Graphs,
CPMs & Geiger counters, Food, Graphing, About, Beaches,
G-M tube failure, Networks, My choice of units, Statistics, Question,
Submersion test, A typical day graph, Reminders,
Notes & commentaries, Fukushima, Medical technetium-99m,
Radium, My graphing pgm, Network suggestions, Draft letter, Fukushima-3,


5/16/2024 update: Solar Cycle 25 is more active than predicted. Here's a current summary and my earlier comments.

* (7/18/2019): Today's (Brad Friedman) "Bradcast" (stream it or download the MP3) brings the dismaying news that the Trump administration (among its many other environmental outrages) is trying to cut way back on the safety and supervision of our aging nuclear power plants.

* (6/30/2019) :-(   It's turned out that the SBO nature of the Fukushima disaster left both the mainstream and alternative media that I follow with no lasting impression. In the news this past week have been unveiled international threats --deliberately leaked stories about Russia and the United States having planted destructive computer viruses in each other's power grid system controllers. I saw nothing about the consequences of multiple nuke power plant melt downs (hundreds of them!) should those viruses get activated.

My "Background Radiation" Graphs
(start out rather humbly.)

March-April 2011 (10 uR/hr ~ 35cpm with my Medcom Geiger counter, 15.61cpm with my M4011 device, and 14.82cpm with my SBM-20 G-M tube device.)
The Fukushima disaster occured on March 11th.

* These early graphs are based on averaged uR/hr readings, using a Radex 1503 Geiger counter with an SBM-20 tube. I would repeatedly wait out the 1503's internal 2.7 minute averaging cycle, note the reading, then average those averages. The 1503 will not display CPMs.

22nd: That peak is probably no more significant than the next. I was only taking 2.7 minute counts (+/- 7.2cpm or +/- 2uR), but went to 10.7 minute averages on the 24th (+/-3.6cpm). (I was using twice the "standard error", based on the square root of the assumed total count.)


April-May 2011

May-June 2011

June-July 2011 (uR/hr)

August 2011
(Dropped back to 5x averaging on August 6th. Note that days pass between readings.)

September 2011

October 2011 (uR/hr)

November 2012

December 2011
(Dropped back to 5x averaging on August 6th. Note that days pass between readings.)

January 2012 (uR/hr)

February 2012

March 2012

April 2012 (uR/hr)

May 2012
The graphs beyond this point change scale and are primarily calibrated in (Medcom "Inspector") CPM,
sometimes with supplemental uR/hr equivalents on the right margin. (10 uR/hr = about 35cpm with the Medcom Geiger counter)

June 2012

July 2012

August 2012

September 2012
* That increase in variation after the 11th is due to reducing the averaging period from hours to 100 minutes. We expect +/-0.6cpm of jiggle at this level of detection and averaging of "Poisson distributed" radiation data.

October 2012

November 2012

December 2012

January 2013
23rd: Confirmed high BG with 2 extra mid-day 100min counts;  26th:  +24.5/14.4cpm mid-day AFs. (Mid-day 10min BGs of 38 & 41.2cpm.)

February 2013

March 2013

April 2013

May 2013

June 2013

July 2013

August 2013
1st: * See my notes about elevation tests with a Geiger counter.

26th: * Those large dots are 100 minute averaged readings made with my "Inspector" Geiger counter (sealed inside a thin "ZipLoc" plastic bag). Note that the last dot is double, the lower blue dot being the count with beta radiation blocked. The smaller black dots are 26.66 minute Radex RD-1503 (SBM-20) averages, taken over a period of about 30 minutes, expressed in "Inspector" (LND-7317) nominally "equivalent" (for gamma) CPMs, for which totals, the standard error is +/-2.6cpm.

* It appears that the large black dot, 5-day whoop-de-do on this graph is all about beta radiation --the stuff I wait for to go away before testing my air filters for residuals. There was no rain until until the 25th, so the invasive beta (radon daughters, presumably) might have been driven out of all the sand around here by our sunny warm days of late. (The 26th was especially warm, but also windy and dry.)

* On the 25th I ran inside and outside tests which included using my old Radex-RD1503 Geiger counter.  Like in the past, I saw no increase when I took it outside (actually getting a slightly lower reading), whereas the Inspector, with its mica window, reads about 11% higher in the same location. This is most likely because the RD1503 is less sensitive to beta radiation.

* It started raining again while I was running the outside RD-1503 count, but there was no effect upon the last 5 readings^. Nor did the rain and steady drizzle of the 25th seem to affect the "Inspector's" readings.

^ The RD-1503 has neither a long count timer nor a data port, so I have to take a reading every 3 minutes in order to build up a longer average --than I can get from its native 160 second cycle. However, it still seems stable and in calibration, so I'll use it for my outside counts. (The exercise will do me good :-)) My purpose in this is to possibly get an earlier warning, should fall-out or volatilized gamma emitters from the beach begin accumulating. (We're fairly close to the bay and Pacific ocean.)

* Note that the last big dot is double. The lower blue one is the Inspector's average with beta blocked. Laying the beta blocked "Inspector" Geiger counter on the ground gave nearly the same reading: 36.33cpm. Removing the beta shield ran it up to 44.37cpm (off the chart, but that's mild, compared to some of the beta CPMs we read about elsewhere after "rain-outs" (or "rain-ups" --not sure).

* Having reverted to placing my old Radex-RD1503 Geiger counter out in the yard (34 inches above ground) for a 26.66 minute averaged count, I'm multiplying the indicated "uR/hr" by 3.5 for a rough "Inspector" Geiger counter equivalent.

* I deal with our radon CPMs to some extent when I do air filter readings, recording the initial value and their signature rate of decay.

28th: * No Radex outside check (small dot) today.

29th: * I ran the outside Radex Geiger counter (SBM-20 tube) check twice, once open, again with 1/8" aluminum shielding: no difference--but that was anticipated, since past outside versus inside Radex checks showed very little difference. After a series of bench tests with potassium chloride and varying aluminum shielding, it appears that the Radex behaves as if it has about .009" of aluminum shielding (over an imaginary mica window). The impression I get is of very weak (under 100KeV) beta at 34 inches off the ground --which changes my gnotion of what "half value layer" (HVL) means with respect to beta. I thought that the intensity of beta electrons was only "depopulated" to 50% by an HVL (at whatever associated KeV), but that the energies of the remnant beta stayed the same. (Obviously, gamma behaves on the depopulation model, since passing light through a 0.3d (50%) neutral density filter does not change its color, and since useful gamma spectrometry can be performed on the radiation escaping (say) the large cadaver of an ocean creature, or the living body of a "nuclear medicine"/imaging patient.)


September 2013a
1st: * No Radex readings today.

September - 2013b
* 8th: Added this 2nd September graph, based on SBM-20 Geiger-Mueller tube sensitivity --after the LND-7317 G-M tube in my Medcom "Inspector" Geiger counter failed. An SBM-20 runs at 15cpm in a 10uR/hr gamma field (from Cs-137), while an LND-1317 runs at 35cpm.
* 13th: A stray cat delivered 5 kittens under our deck, which has been taking up a lot of time --getting them in, taming, arranging for spay/neuter and adoption --so: my readings are down to little more than once per day for a while.
* Please note that with the smaller tube and shorter (cumulative) counting period, I've more than doubled the "noise"/jaggedness of my graphing. The "standard deviation" is +/-0.9cpm (or let's say: +/-1cpm --at an average of 15cpm) --and it shows.

October - 2013

A map of our two field stations, our fixed outdoor Geiger counter and our portable Geiger counter

*5th: Was able to install a Russian SBM-20 G-M tube in my failed Medcom "Inspector" Geiger counter. I've got about 43% of the Inspector's original gamma sensitivity, plus I've lost the ability to detect alpha and soft beta radiation --but I can once again do automatically timed counts plus participate on-line with Radiation Network.
*9th: We selected two remote locations for 30 minute monitoring counts: 4.7 miles in from the mouth of Coos Bay (EBR = Empire Boat Ramp) and two miles south of the mouth (SB = Sunset Bay). We'll check these high tide spots throughout the year. (See 2015 entry, just below.)
*27th: Resumed doing periodic air filter monitoring, but drawing about 4.4 cubic meters of air over 15 minutes --instead of the old 10 cubic meter standard. The buildups in the filters were weak, with 50% more CPMs (at about  2x background) in the draw taken 2 inches off the ground, than in the filter drawn at 12 feet above ground level. Of necessity, only a 10 minute initial reading, then another 40 minutes later, were taken. Consequently, the possible errors were large, but the decays were: to 69% (2 inch high draw) and to 43% (12 foot high draw) over 40 minutes.
*28th: Tested the two air filters of the 27th, finding their gamma and hard beta radiation to be indistinguishable from the background level.
*5/25/2015: Have mostly discontinued the remote 30 minute counts in favor of 2.7 minute averaged roving beach wanders (with our dog Sammy). A shirt pocket Geiger counter (Radex RD1503) is set to audible, so the ear sensitivity to anomalies adds considerably to the nominal +/-16% sigma/standard deviation of the display (which is checked periodically). Have added Bdrf = Bastendorff (just north of Sunset Bay).
**11/2/2020 update: The (Coos River) Chromium mining/mill having shut down some years ago, I now only do "beach wanders" at Bastendorff Beach (Sunset Bay being redundant). Instead of a long count with a tripod mounted Geiger counter, these are 10 minute walks along recent high tide "froth lines", listening for anomolous clicking indications of any hot particles ("fuel fleas"), then recording the averaged CPM of my gamma sensitive Geiger counter at about 30 inches above the sand. I graph these counts as a percentage of what's been my base-line normal at the house --for my SBM-20 tubed Medcom "Inspector" Geiger counter.


November - 2013
*EBR, SB and Home: see note on the October graph.
*28th: Ran an air filter draw, finding the initial CPMs reading clearly at 4.5x background in the test jig. The decay rate (to 73% at 20 minutes) had a radon daughter profile. The filter read at background, 24 hours later.

December - 2013
5th: * Began monitoring with the new outdoor station.
11th: * Began 60 minute counts at home (30 minutes at remote Empire Boat Ramp and Sunset Beach stations).
16th: * Began 24/7 air sampling at low velocity (1.36 cubic meter/day, instead of sporadic draws of 4.4 cubic meters in 15 minutes).
19th: * With the approach of winter storms and continuous air sampling, the intake was lowered to 9.6 feet above the ground.
20th: * Have both a beach sand sample and 3 air filters (1st low velocity and 2 old filters) on their way for gamma spectrometry.
24th: * The new outside monitoring station seems stable. Will begin running it continuously on-line with Radiation Network.
26th: * Stopped 24/7 air sampling. Filter was soaked from condensation.
* EBR and SB: see note on the October graph.

January - 2014a

January - 2014b
11th: * I'm not satisfied with any of the graphing modes I've tried (and see below).
22nd: * Did two 65 minute (19.1 cubic meter) filtered air draws today, getting unusually high initial radon/daughter readings (9x and 12x background) which decayed to 51% and 50% in 40 minutes (gamma and hard beta only). They'll be examined with gamma spectrometry.
26th: * Air filter update. The 9x filter checked out as having no residuals. (Thanks, Tom.) We're still waiting for a report on the 12x filter. (2/22: I never did get a final analysis on the 12x, but the preliminary graph implied that the lab (not Tom's) didn't have enough substance on the filter to get readings sufficiently above background. I thank both labs for having a go at my air filters and I'll be quadrupling my air draws.)
29th: * I'll be going from 1 inch to 2 inch diameter air filters here. I get about the same volume rate (limited pumping and plumbing capacity) but the flow rate per square inch will be 25% as much (better?) and the filter size is a better match to a 2" scintillator crystal.
30th: * There was no evidence of the M6 solar flare today at 08:17 PST (16:17 UTC/GMT) in my minute-by-minute counts. However, there was an isolated, 1 minute, greater than 4 sigma of 33cpm at 07:35 today.
I'll continue watching for and noting any unusual short term spikes at my station. Unless grouped, isolated spikes of less than 4 standard deviations/"sigmas" will be ignored, since 3 sigma counts occur several times per day --by statistical probability alone. At a station average of 16cpm, a 4 sigma spike would come in at 32cpm (by my calculation).

February - 2014
* Days during which my minute-by-minute CPMs reached 33cpm or higher: 2/1 (33), 2/12 (33), 2/13 (33), 2/14 (34), 2/16 (33).
22nd: * We had two dry sunny days in a row, so I checked the beach stations and did a 40 cubic meter air draw, getting what's apparently radon/daughters (40 minute half-life) with an initial reading of 5x background.
23rd: * After 39 hours, the air filter read at a normal background level.  I'm sending this filter to Tom's lab for gamma spectrometry.

March - 2014
2nd: * Began adding 12 hour daytime though evening averages as unconnected small black dots. (Might not catch every day's count.)
13th: * An isolated single minute count of 33 at 21:42 hours.
20th: * An isolated single minute count of 33 at 11:19 hours.
22nd: * Gave up on 24 hour averages (as being not much different than 12 hours) and went to all 12 hour --and all connected on the graph.
28th: * Whoops: shut down the computer before I saved my CPM data --but it was running 15-something, per usual. (My dog's fault! :-)

April - 2014
13th: * There was an isolated one minute count of 32 at 20:34 hours PDT. Presumably, this was a random high (re: "Poisson distribution").
14th: * A rather high reading at the Empire Boat Ramp today, but not at Sunset Beach. EBR was higher in February as well.
* "100%" was (arbitrarily) normalized to the last week in January --which appears to have been a few percentage points higher than the annual normal average. I'll stick with it never-the-less.
15th: * There was an isolated one minute count of 33 at 14:17 hours PDT.
16th: * There was an isolated one minute count of 34 at 19:49 hours PDT.
20th: * Whoops: forgot to turn the data logging program on today --sorry.

May - 2014
9th: * There was an isolated 32cpm one minute spike at 23:45 hours PDT.
12th: * Got another high reading at the Empire Boat Ramp today --though not a record, and Sunset Bay was fairly high as well. Both readings were above clearly delineated (by detritus and seaweed) high tide/wave wash lines.
* Again: I originally expected Sunset Bay to be higher, since it opens upon the ocean --particularly as we anticipate the Fukushima plume's arrival. It might be that the Empire Boat Ramp station (4.7 miles up into the outflow of the Coos River) is located on dredgings which happen to be more radioactive. Another possibility is forest run-off, abandoned and current mining operations further up the river.
* I'm torn as to whether I should always station on the same maximum tide line spot, or follow the most recent/apparent high water line as it advances and recedes. If I keep so moving the station, I might cross a vein of thorium rich sand and get a false impression about encountering evidence of the Fukushima plume. What's your opinion?
* I also did an air draw today. It was supposed to be 2 hours (40 cubic meters), but I drifted off to sleep and it ended up being a 140 minute draw (47 cubic meters). The initial N95 filter activity was fairly low (4.4x background) and it decayed at a classical radon daughter rate (to 48% in 40 minutes, counting gamma and beta only). After 49 hours, the filter checked at background, so there were no residuals that I can detect.
16th: * There was an isolated 33cpm one minute spike at 15:06 hours PDT.
18th: * No birds at the feeders this morning --very unusual, but has happened once before. We normally have 15 to 20 pigeons and dozens of chirping small birds (sparrows, blackbirds, cow birds, crows). They must have come later, but not enough of them to scour the bottom of the elevated small bird feeder.
19th: * Up to 15 pigeons trickled in, but initially, no small birds again.
22nd: * There was an isolated 32cpm one minute spike at 09:01 hours PDT. (Will begin noting spikes at 33cpm after this entry.)
24th: * Sorry! I flat forgot to turn the data logging on today.
* Back to normal on pigeons, small birds still somewhat diminished.

June - 2014
05th: * No pigeons, sufficient small birds at the feeder.
06th: * 6 pigeons, sufficient small birds at the feeder.
07th: * 12 pigeons, normal number of small birds.
10th: * Pigeon and small bird count back to normal. (Turns out a family of feral cats moved in.)
* Did an air draw today: 40 cubic meters. The initial N95 filter activity was quite low (1.7x background). After 24 hours the filter checked at background, so there were no residuals that I could detect.

July - 2014
10th: * There was an isolated 34cpm one minute spike at 12:02 hours PDT.
12th: * Did our monthly 40 cubic meter air draw --through a small N95 filter. The initial CPM was exceptionally low: 56% above background, which then decayed exceptionally fast --to 15% in 40 minutes --perhaps because my deviation errors ganged up on me this time. (I'll try to get this air draw data onto the above graph, which will be periodically posted to: http://radviews.com.)
27th: * Isolated 34cpm spike at 10:37 hours PDT.

August - 2014

September - 2014

October - 2014

November - 2014

December - 2014

January - 2015

February - 2015

March - 2015

April - 2015
% deviation from 293.2o Kelvin G-M tube temperature (-5%) from 4/19/2015

May - 2015
5/25b: * I've discontinued my remote station 30 minute beach and bay counts in favor of "beach wanders" (with our dog Sammy), while carrying a beeping Radex-RD1503 in my shirt or jacket pocket (for pretty much of a gamma count only). While the display count is only averaged over the previous 160 seconds --for a whopping standard deviation of +/-16% (+/-2.5cpm), the ear is oddly more sensitive to changes than that would suggest. The advantage is in greatly expanding the area I'm monitoring, but only for detecting something gross --like "hot particles" or a hot object, since there'll no longer be a fixed station base line. However: should I log a significant average increase or an anomaly, I'll do a better count. I've added station Bastendorff ("Bdrf") --between Sunset and the Empire Boat Ramp.

June - 2015

6/9b: * I don't know what these peaks are about, but that 24 hour average is a whopping 17.7 standard deviations ("sigma") over the 15.77cpm norm here (at least: the way I figure it). As shown below, the day's 60 minute averages, 10 minute averages and one minute counts are no slouches either. (Ctrl+ to enlarge the images.)


One and Ten Minute Averages on June 9th, 2015
(Ctrl+ to enlarge the images.)


Hour-long averages on June 9th, 2015
(I'm guessing this is a rounded running average.)


Hour-long averages on June 10th, 2015
(This appears to be an hour-by-hour straight average, based on a different output of GeigerGraph data.)


Hour-long Averages, June 1st through 9th, 2015

6/10c: The high count experience here seems to have been isolated to my station. Judging by the period of hours that it appeared to last, I speculated that I was picking up radiation from a neighbor who'd been given a radioactive tracer injection (ie: "nuclear medicine"), although I have no confirmation of that.

6/11: * Okay --I'm stumped. Assuming this is about a neighbor who's been given a medical dose of a radioactive tracer substance, a second day of high CPMs suggests that it can't have been 6 hour half lived technetium-99m (which is rapidly eliminated from the body). Possibly, the tracer was iodine-131, but for all I know, my elevated CPMs were caused by something else altogether.

* I compared my regular Geiger counter to one which use to match its counts fairly well (long term averages), and found it about 5% higher now. Since my graphs have otherwise been looking consistent, I'm saying that the 2nd Geiger counter was 5% low --for some reason.

* I did a 4 loop "beach wander" today, since there's so much in the (Ene) news about ocean contamination, but my readings were normal --and I was listening to the beeps as I walked. (I saw the same bands of --what I take to be-- small, dead, paper thin jelly fish --as before.)

6/16: How to log and graph such a rough and casual reading is a problem. Tentatively, I'll average the displayed range of readings and "round up" to the nearest 10% --as looked at and informed by the audible beeps.

Sorry: Save for an active period late in November, I got discouraged and stopped graphing --until 2016, preserving only my logged notes for unusual peaks/events (as follows). However, the logging program I've been using (an old beta version of GeigerGraph-5) can be set to generate an hourly averaged graph for that period (shifted about 8 hours on 10/10/2015, when I went to UTC time) with overlap in June for comparison:

--which you'll have to Ctrl+ to enlarge the images and read the legends. (PDT time)

That period of interest in June (PDT time).

July - 2015: * There were isolated (ie: no preceding build-ups nor follow-on decays) one minute long peaks on the 4th (33cpm), the 8th (34cpm), 25th (33cpm), but the days of July otherwise looked normal.

August - 2015: * There were isolated 33cpm (minute-long) peaks on August 21st, 23rd, 26th, and 28th. We logged isolated 34cpm peaks on the 22nd and the 26th as well. Those peaks were statistically unsurprising and the rest of August has been within our normal range.

        (I'll try to make my reporting more uniform.)
September - 2015: * We logged peaks as follows:
    ~33cpm at 08:37 hours (all PST) on 9/7
    ~33cpm at 20:22 hours on 9/9
    ~34cpm at 07:20 hours on 912
    ~33cpm at 00:22 hours on 9/16 (The 10 minute running avg hit my reporting threshold of 20cpm 00:30h)
    ~The 10 minute running avg hit my reporting threshold of 20cpm on 9/20 at 12:00 hours
    ~34cpm at 11:25 hours on 9/22
    ~34cpm at 12:23 hours on 9/24 , and on the 20th at 12:00 hours.
    ~37cpm peak on 9/24 at 13:50 hours --a bit unusual
Other than those of the 24th, September's peaks were isolated (ie: no preceding build-ups nor follow-on decays) and statistically unsurprising. The rest of September was within our normal range.

October - 2015: * I'm reading responsible reports that cesium-137 is showing up in Alaskan waters.

* As of 10/10/2015 I standardized on Co-ordinated Universal Time, or "UTC" --which is similar to GMT", but sans any DST changes. I should have been doing this since March of 2011. (We need to don pirate costumes and form a rabid, single issue political faction which is hell bent on abolishing our absurd Daylight Saving Time clock changes --!-- Arrrrrr!)

 * As of 10/31/2015, logging here has been within our normal range, with isolated peaks (ie: no preceding build-ups nor follow-on decays) as follows:
    ~33cpm peak at 17:30 hours on 10/2
    ~34cpm peak at 20:49 hours on 10/9
    ~34cpm peak at 09:33 hours on 10/10 (Switched to UTC time-dates)
    ~33cpm peak at 06:13 hours on 10/25 (10 minute avgs reached 20cpm 4 times --otherwise isolated.)
    ~33cpm peak at 00:19 hours on 10/26

November - 2015: * As of 11/30/2015, and except for a double-peaked 10 minute running average excursion on the 30th (to 22cpm, but 1 minute peaks did not reach 33cpm), logging here has been within our normal range, with isolated peaks (ie: no preceding build-ups nor follow-on decays) as follows:
    ~The log for the day of 11/2 was somehow lost.
    ~The 10 minute running average reached my reporting threshold of 20cpm at 08:30 hours on 11/4.
    ~The day's 24 hour average was 15.64cpm on 11/10 (The 7-day average ending 1/31/2014 was 15.77)
    ~The 10 minute running average reached 20cpm at about 01:39 hours on 11/15.
    ~The 10 minute running average reached 20cpm at about 16:15 hours on 11/17.
    ~33cpm peak at 10:30 hours on 11/18
    ~On 11/20 I started saving images of the daily graph (to the default directory for GG-5b).
    ~The 10 minute running average reached 22cpm at about 17:00 hours on 11/20.
    ~35cpm peak at 10:46 on 11/22.
    ~The 10 minute running average reached 20cpm at about 05:30 hours on 11/24.
    ~The 10 minute running average reached 23cpm at about 20:00 hours on 11/24.
    ~The 10 minute running average reached 20cpm at about 09:30 hours on 11/25.
    ~33cpm peak at 12:51 hours on 11/25.
    ~34cpm peak at 23:50 hours on 11/26.
    ~The 10 minute running average touched 20cpm 3 times on 11/29.
    ~The 10 minute running average touched 20cpm 3 times on 11/30 --once to 22cpm, but no 33cpm 1-min peaks.


11/28-11/30/2015utc (Ctrl+ to enlarge the images.)

December - 2015: * As of January 1, 2016, logging here has been within our normal range, with isolated peaks (ie: no preceding build-ups nor follow-on decays) as follows:
   ~34cpm peak at 15:12 hours on 12/1.
   ~The 10 minute running average reached 20cpm at about 13:00 hours on the 4th.
   ~The 10 minute running average reached 20cpm at about 18:00 hours on the 6th.
   ~The 10 minute running average reached 22cpm at about 14:30 hours on the 8th.
   ~The 10 minute running average reached 21cpm at about 16:00 hours on the 10th.
   ~The 10 minute running average reached 20cpm at about 09:00 hours on the 11th.
   ~33cpm peak at 00:56 hours on 12/17.
   ~The 10 minute running average reached 20cpm at about 05:15 hours on the 18th.
   ~On 12/24, I started logging (but I'll usually not post) the 24 hour average for each day. I'm also saving the daily graphs. The first averages have been: 15.75, 15.12, 15.38, 15.33, 15.17, 15.44, 15.39, 15.20 (through 12/31). these average 15.35cpm, whereas the last week of January, 2014 averaged 15.77 (with the same outside-inside  equipment and configuration).
   ~33cpm peak at 20:43 hours on 12/26.

January - 2016
* All times/dates UTC. As of January 19, logging here has been within our normal range, with isolated peaks (ie: no preceding build-ups nor follow-on decays) as follows:
   ~4th: The 10 minute running average reached 20cpm at about 23:15 hours.
   ~5th: The 10 minute running average reached 20cpm at about 13:15 hours.
   ~Somehow, the program shut down on the 6th, so I lost the data for the 6th-7th period.
   ~7th: The 10 minute running average reached 20cpm at about 17:50 hours.
   ~7th: 33cpm peak at 18:10 hours.
   ~9th: The 10 minute running average reached 23cpm at about 18:17 hours.
   ~12th: The 10 minute running average reached 20cpm at about 17:00 hours.
   ~15th: 33cpm peak at 01:44 hours.
   ~17th: 33cpm peak at 08:07 hours.
   ~18th: 33cpm peak at 05:09 hours.
   ~19th: 33cpm peak at 11:38 hours.
   ~No 4.4+ sigma peaks through to the 31st, and the averages are running low.

* I'll continue to base percentages on year 2014 being 100% (15.77cpm).

* Why do the 1 and 10 minute averaged levels of 33-34cpm and 20cpm repeat so often? This has to be some sort of an event with an irregular but frequent recurrence. I checked the USGS "Real-time earthquake map" (via the R-G Oregon Live Link) and tallied 9 small earthquakes spanning the past 30 days --within a radius of about 130 miles (land and ocean). None of them came even close to the UTC timed peaks on this page.

* Perhaps I can get some regional magnetometry to match up.

* We've recently had a few frog drowning rainfalls, but with no marked effect upon the gamma counts that I can see. Perhaps if I compared rainfall rates to the rolling 10 minute averages, I could see some match-ups.


February - 2016
* All times/dates UTC. As of February 17, logging here has been within our normal range, with isolated peaks (ie: no preceding build-ups nor follow-on decays) as follows:
   ~2nd: The 10 minute running average reached 21cpm at about 05:00 hours.
   ~2nd: 32cpm peak at 21:07 hours, noted because it was such a stand-out peak (although less than 33cpm).
   ~3rd: The 10 minute running average reached 20cpm at about 19:30 hours.
   ~I stopped saving daily graphs as of the 3rd.
   ~9th: The 10 minute running average reached 20cpm at about 20:15 hours.
   ~15th: 33cpm peak at 06:29 hours.
   ~The daily average fell to 94.6% on the 16th, so I decided to do a graph for the month of February as well --and to corroborate January's low average. Past graphs have dipped as low as 91%, however. There's been one power failure (a broken wire) and time will tell if this is about the (sealed in with the Geiger counter) backup battery running down, but I don't think so.
   ~17th: Noted: an abrupt increase of 5.2% in the daily average.
   ~18th: The 10 minute running average reached 20cpm at about 15:15 hours.
   ~21st: The 10 minute running average reached 20cpm at about 14:15 hours.
   ~23rd: The 10 minute running average reached 20cpm at about 07:00 hours.
   ~Oddly, that 10 minute average "ceiling" pretty much continues.
   ~No other notable excursions through the end of this month.
   ~The last 7 days of February averaged 97.3% --a tad higher than the last 7 days of January.

March - 2016:

* As of 4/1/2016, logging here has often been below our normal range, with isolated peaks (ie: no preceding build-ups nor follow-on decays) as follows:
  ~  5th: The 10 minute running average reached 20cpm at about 22:10 hours.
  ~  5th: 33cpm peak at 21:58 hours. (A brief decay, but no build up. Saved the graph.)
  ~  7th: Found the logging program stopped. Rebooted the OS.
  ~12th: The 10 minute running average reached 20cpm at about 12:15 hours.
  ~19th: 36cpm peak at 04:23 hours. (No build up, brief 10m avg plateau at 18cpm.)
  ~20th: The 10 minute running average reached 20cpm at about 06:00 hours.
  ~21st: The 10 minute running average reached 20cpm at about 12:00 hours. (isolated)
  ~21st: The 10 minute running average reached 20cpm at about 18:30 hours. (isolated)
  ~22nd: 33cpm peak at 03:04 hours. (The average over the past 3 days: 15.51 = 98.35%)
  ~23rd: This day's average fell to 14.98cpm = 95% --the 3rd such low this year.
  ~24th: Only got the last 12 hours of this period (forgot to restart the logging program in the morning).
  ~29th: The 10 minute running average reached 20cpm at about 15:45 hours.
  ~30th: The 10 minute running average reached 20cpm at about 10:50 hours. (isolated peak)
  ~30th: The 10 minute running average reached 21cpm at about 11:20 hours. (isolated peak)
  ~31st: The last 7 days averaged 96.8% of this station's 2014 baseline (100% = 15.77cpm).


April - 2016:
* The following comments are based on whole counts.

* As of 5/1/2016, my counts have been trending back up toward our normal range, with isolated peaks (ie: no preceding build-ups nor follow-on decays) as follows:
  ~  2nd: The 10 minute running average reached 20cpm at about 04:30 hours.
  ~  7th - 8th: I found the GG-5 logging program off. Rebooted the operating system.
  ~10th: 32cpm peak at 14:30 hours.  (From graph only. GG-5's SS overwrote data after the 3rd day.)
  ~14th: The 10 minute running average reached 20cpm at about 06:40 hours.
  ~15th: 32cpm peak at 01:46 hours.
  ~17th: 32cpm peak at 00:42 hours, and again at 02:30 hours.
  ~22nd: The 10 minute running average reached 20cpm at about 16:15 hours.
                (I don't know why the 10 minute count is so often 20cpm.)
  ~30th: The rest of April was "low" to "average" with no one or ten minute peak reaching levels of note.


May - 2016
A comparison of straight counts logging to my (brief) "minus noise" logging.

* As of 6/1/2016, my counts have been trending back up toward our normal range, with peaks (one of which appeared to be a build-up and decay) as follows:
  ~  1st: 33cpm peak at 20:24 hours (UTC).
  ~  3rd: The 10 minute running average reached 20cpm at about 10:00 hours.
  ~  6th: 32cpm peak at 16:30 hours.
  ~  8th: The 10 minute running average reached 21cpm at about 00:30 hours.
  ~  8th: 33cpm peak at 03:52 hours.
  ~10th: The 10 minute running average reached 20cpm at about 15:00 hours.
  ~10th: 33cpm peak at 22:17 hours.
  ~11th: 32cpm peak at about 10:45 hours.
  ~13th: 34cpm peak at 06:06 hours.
  ~13th: The 10 minute running average reached 20cpm at about 13:15 hours.
  ~14th: 32cpm peak at 11:17 hours.
  ~14th: Another 32cpm peak at about 14:30 hours.
  ~17th: The 10 minute running average reached 20cpm at about 12:45 hours.
  ~20th: Found my logging program stopped and data lost for the day. Rebooted OS.
  ~21st: 32cpm peak at 19:25 hours.
  ~21st: The 10 minute running average reached 20cpm at about 19:40 hours (almost a decay from that 32 peak,
              but looks more like a coincidental stand-alone). Saved graph and SS.
  ~23rd: The 10 minute running average reached 20cpm at about 06:45 hours.
  ~24th: 33cpm peak at 06:22 hours.
  ~25th: 32cpm peak at 13:20 hours. (Saved SS & graph. Submersion tests today.)
  ~28th: A 33cpm peak at 15:24 hours, surrounded by a brief build-up and decay --which amounted to a 10 minute
             running average peak of 21cpm at about the same time. Although these peaks, alone, are barely
             remarkable, a "build-up and decay" is unusual enough to take note of (if not graph).
  ~30th: The 10 minute running average reached 20cpm at about 22:05 hours. (Today's average reached 100.1%)
  ~31st: The 10 minute running average reached 20cpm at about 08:15 hours. (Today's average reached 102.4%. )


June - 2016
(Apologies: This graph evaporated for a few days.)

* My notices of higher peaks were growing rather lengthy --now that "background" radiation counts are returning to the 2014 baseline average (15.77 = 100%), I've arbitrarily raised the bar --to a whole count of 22cpm for 10 minute running averages (140% of  baseline), and to a one minute count of 33 (209% of baseline).

* G-M tube mid-level energy gamma efficiency might only be about 2%, but G-M tubes will continue to count up into Cosmic energy levels (well above scintillator levels) so G-M tubes might have good response to muons (flux ~ 1/cm^2/minute, they carry charge & are some 200x the mass of an electron, so the shielded noise count seems about right, given the profile of an LND-7317 G-M tube). An argument against: they're relativistically fast enough to only be perceptually present --and don't hang around long enough to ionize G-M tube gas. (Muons collide with and get amplified by lead shielding due to secondary splatters --to the extent that counts can go up with over 100mm of shielding.)

~  9th:  The 24 hour run ending today averaged 101.8 percent.
~10th:  33cpm peak at 12:32 hours (UTC).
~11th:  The 24 hour run ending today averaged 101.8 percent.
~18th:  A 33cpm peak at 06:50 hours.
~18th:  A 33cpm peak at 07:17 hours.
~22nd:  Found my logging program stopped and data lost for the day. Rebooted OS. Due to the increasing
             frequency of my logging program crashes, I'm scheduling OS reboots every 8 days now.
~30th: Above times UCT/GMT. No further threshold crossing peaks to report, as of this (PST) morning.


July - 2016
~  2nd: 34cpm peak at 10:15 hours (UTC). (Isolated)
~  2nd: 35cpm peak at 14:43 hours. (Isolated)
~15th:  35cpm peak at 02:45 hours. (Isolated, but saved automatic day graph anyway.)

This is a typical graph, probably including that 35cpm spike plus all the lesser ones. Catching and
counting gamma rays is similar to counting people passing through the gate at your county fair --per
minute. Sometimes a bunch goes through, sometimes hardly anyone, and you can expect a distribution
of counts over time (a "Poisson distribution") that's similar to this graph. I'm going by results now (like: "how
often do I get a given peak?", rather than calculating so many "standard deviations" from a long term average --and
by whether the graph appears to show a build up to a bit of a high plateau --rather than throwing a one-off "isolated" peak.

~21st: Lost data, so only the late night and early morning 10 hours, which I "corrected" by +2.1%, based on a
           recent day-to-night averaging comparison.
~22nd: 33cpm peak at 05:16 hours (UTC). (Isolated)
~31st: Above times UCT/GMT. No further threshold crossing peaks to report, as of this (PST) morning.


August - 2016
~   8th: 33cpm peak at 09:50 hours (UTC). (Isolated)
~   9th: 34cpm peak at 04:12 hours. (Isolated)
~   9th: 33cpm peak at 19:24 hours. (Isolated)
~ 14th: Was only able to monitor and average the last 11 hours of this 24 hour period.
~ 18th: 34cpm peak at 11:59 hours. (Isolated)
~ 20th: 33cpm peak at 03:35 hours and another 33cpm peak at about 09:00 hours. (Both isolated)
~ 24th: 34cpm peak at 19:23 hours. (Isolated.) Noted: similarly timed peak on the 9th. High 102.7% average.
~ 25th: 33cpm peak at 23:20 hours. (Isolated.)
~ Note: single, one minute peaks are accurately timed (UTC), while subsequent peaks or high 10 minute averages must be estimated from their positions on GeigerGraph plots (which have peculiar time intervals).
~ 31st: Above times UCT/GMT. No further threshold crossing peaks to report, as of this (PST) morning.

September - 2016
~   1st: 33cpm peak at 09:50 hours (UTC). (Isolated)
~   28th: 34cpm peak at 07:06 hours. (Isolated)
~   30th: Above times UCT/GMT. No further threshold crossing peaks to report, as of this (PST) morning.

October - 2016
~   2nd: 35cpm peak at 03:58 hours (UTC). (Isolated)
~   3rd: 33cpm peak at 12:16 hours. (Isolated)
~ 11th: 35cpm peak at 07:16 hours. (Quite isolated --from a very quiet looking graph (saved).)
~ 12th: 33cpm peak at 13:01 hours. (Isolated, but my 24 hour average is up. Saved graph and spreadsheet.)
~ 15th: Stormy weather, but doesn't appear to affect the graph (nor in years past records).
~ 27th: 33cpm peak at 22:11 hours. (Isolated)
~ 31st: Above times UCT/GMT. No further threshold crossing peaks to report, as of this (PST) morning.

November - 2016
~   6th: 33cpm peak at 20:06 hours (UTC). (Isolated)
~ 18th: 33cpm peak at 14:49 hours. (Isolated)
~ 21st: 33cpm peak at 10:03 hours. (Isolated)
~ 23rd: 34cpm peak at 16:23 hours. (Isolated)
~ 30th: Times are UCT/GMT. No further threshold crossing peaks to report, as of this (PST) morning.

December - 2016
~   3rd: 37cpm peak at 13:50 hours (UTC). (Isolated)
~   9th: 37cpm peak at 16:17 hours. (Isolated)
~ 11th: 33cpm peak at 10:37 hours. (Isolated)
~ 12th: 35cpm peak at 11:52 hours. (Isolated)
~ 14th: 34cpm peak at 01:50 hours. (Isolated)
~ 15th: The past 24 hour average reached 104.1% this morning. Otherwise, the daily graph looks normal.
~ 19th: A run-up and then down --as noted.
~ January 1st: Times are UCT/GMT. No further threshold crossing peaks as of this morning.
~~~~~~~~~~~~~~~~
A comparison of my monitoring in Oregon, USA with Peter Daley's in Australia:
* That mid-month rough correspondence suggests that we might be looking at a commonality of cosmic radiation,
perhaps with influence from the recent solar winds --plus overlays of more local phenomena and "noise".

* One gets the impression that there was some kind of an event spanning the 17th through the 19th. / The solar notations are from my readings/interpretations of Dr. Tony Phillips' daily descriptions at Spaceweather.com.

* Some are of the opinion that solar winds and other activity "sweep away" a lot of the primary cosmic rays (from deep space), the secondaries of which (mostly muons near sea level) make up half or more of the "background radiation" that Geiger counter type monitoring stations tally up.

* If I get another distinctive looking graph, I'll compare data again.


January - 2017
~   5th: Don't know what to make of that saw tooth. We had 4.5 inches of fluffy new snow on the 4th.
~ 31st: No threshold crossing peaks as of this morning. There was only one sun spot this past month (that I recall)
            but a lot of solar wind --for which you can check the record at: Space Weather

February - 2017
~   3rd: 33cpm peak at 10:00 hours (UTC). (Isolated)
~   5th: 33cpm peak at 18:16 hours. (Isolated)
~ 21st: 33cpm peak at 09:45 hours. (Isolated)
~ 24th: 34cpm peak at 08:08 hours. (Isolated)
~ 24th: 33cpm peak at 09:00 hours (+/-). (Isolated)
~ March 1st: No other threshold crossing peaks as of this morning.

March - 2017
~ For months there's been too much recent rainfall to do a beach walk reading (cesium being water soluble).
~ March 31st: No threshold crossing peaks as of this morning.

April - 2017
~   7th: 34cpm peak at 18:59 hours (UTC). (Isolated)
~ 30th: No other threshold crossing peaks as of this morning (PST/PDT).

May - 2017
~  25th: 34cpm peak at 08:26 hours (UTC). (Isolated)
~  31st: No other threshold crossing peaks as of this morning (PST/PDT).

June - 2017
~  8th: The day's graph looked normal --save that the average is somewhat high and the above graph looked like a build-up. (We hit 104% six plus months ago.)
~30th: No threshold (33cpm) crossing peaks as of this morning (PST). We've had five 32cpm peaks this month, all of them isolated --meaning no build-ups and they looked like the high end of statistical noise. However: that there've been no 33cpm peaks is statistically significant.

High altitude counts (see Space Weather) show a marked increase of 10 to 15%, which is attributed to our Sun having entered a quiet period --the solar wind being less able to sweep away incoming cosmic primary rays. Peter Daly's Australia based station has seen just this much of an increase, but my station cleaves doggedly near its long term average of 15.61cpm (= "100%" and approximately an indicated "0.10 uSv" [on a Geiger counter so calibrated in otherwise meaningless Cs-137 gamma "dose" units]).


July - 2017
~   1st:  33cpm peak at 21:34 hours (UTC, isolated).
~   2nd: 33cpm peak at 00:05 hours (isolated).
~   7th:  35cpm peak at 08:27 hours (isolated).
~ 14th:  33cpm peak at 14:39 hours (isolated).
~ 26th:  33cpm peak at 14:23 hours (isolated).
~ 29th:  34cpm peak at 13:41 hours (isolated).
~ 30th:  33cpm peak at 13:33 hours (isolated).
~ 31st:  No other threshold crossing peaks as of this morning (PST/PDT).

August - 2017
~   5th:  36cpm peak at approximately 05:30 hours (UTC, isolated).
~   6th:  34cpm peak at 18:06 hours (isolated).
~ 10th:  34cpm peak at 01:28 hours (isolated).
~ 11th:  Spaced out --doing astronomy projects. Let my Geiger counting go for 2 mornings. I've missed no peaks.
~ 13th:  36cpm peak at 18:16 hours (isolated).
~ 15th:  32cpm --below threshold, but looks like a build-up of peaks at about 21:18 hours.
~ 16th:  33cpm peak at about (isolated). The 24 hour average reached 103% this morning (PST/PDT).
~ 17th:  34cpm peak at 13:09 hours. No avg build-up, but there was a brief "build-up" of peaks (saved the graph).
~ 22nd: 38cpm peak at 13:55 hours --isolated? Minute-by-minute peaks: 17, 20, 20, 38, 20, 16. Hmmmnn.
~ 23rd: This graph and report posted a day early on account of the recent eclipse (morning of the 21st, PST/PDT).
~ 28th:  33cpm peak at 12:05 hours with sort of a following decay.
            * The 24 hour average is "way" up, which is only 6.2% above the station's baseline average, but that's the highest since I started 24 hour averaging in January of 2014.
             * It's probably due to all the smoke in the air from the fierce forest fires burning in Oregon. The smoke particles could be collecting radon. The fires could also be releasing long-lived radionuclides (Cs-137?) which were captured as the trees grew.
             * Another possibility: during the eclipse (morning of the 21st) I noticed significant sunspots. Today the Sun looks clear (at 8 power), and the day's Space Weather indicates that the solar wind is low, but is due to return about August 31st. (The solar wind helps repel primary cosmic rays. Check with Space Weather for more details.)
~ 31st:  No other threshold crossing peaks as of this morning (PST/PDT). The 1, 10, 60 minute graphs and the above 24 hour graph are normal.

September - 2017
~   5th:  34cpm peak at approximately 16:43 hours (UTC, isolated).
~   7th:  Recent X-9 solar flare. A CME might hit us on the 8th.
~   9th:  Two days averaged together --no data lost, no more threshold crossing peaks as of this morning (PST/PDT).
~ 10th:  I saw no indication of either the September 7th CME (arrived on the 10th, producing a "Forbush
             minimum" at south pole) or the September 10th X class flare. See Space Weather for more.
~ 11th:  33cpm peak at 14:31 hours (isolated).
~ 20th:  37cpm peak at 19:32 hours. Isolated, but several curious, somewhat periodic, lesser peaks across graph.
~ 23rd:  39cpm peak at 13:19 hours. Very isolated (12, 20, 39, 17, 21, 10).
~ 30th:  36cpm peak at 12:29 hours (UTC, isolated).
~ 30th:  No other threshold crossing peaks as of this morning (PST/PDT).

October - 2017
~   4th:  33cpm peak at 10:40 hours (UTC, isolated).
~   4th:  33cpm peak at 23:17 hours (isolated).
~   8th:  34cpm peak at 03:18 hours (isolated).
~ 10th:  35cpm peak at 08:30 hours (isolated).
~ 16th:  36cpm peak at 10:14 hours. Isolated (no build up/down). Followed by 2 descending peaks (saved screen).
~ 25th:  33cpm peak at 12:57 hours (isolated).
~ 28th:  36cpm peak at 21:05 hours (isolated).
~ 31st:  No other threshold crossing peaks as of this morning (PST/PDT).

November - 2017
~   7th:  35cpm peak at 09:10 hours (isolated).
~ 13th:  38cpm peak at 01:04 hours (isolated).
~ 13th:  33cpm peak at about 16:00 hours (isolated).
~ 18th:  33cpm peak at 18:06 hours (isolated).
~ 29th:  33cpm peak at 04:12 hours (isolated).
~ 30th:  No other threshold crossing peaks as of this morning (PST).

December - 2017
~  13th:  33cpm peak at 17:38 hours (isolated).
~  14th:  35cpm peak at 04:57 hours (isolated).
~  15th:  33cpm peak at 11:22 hours (isolated).
~  16th:  35cpm peak at 11:16 hours (isolated).
~  25th:  35cpm peak at 08:39 hours (isolated).
~  31st:  No other threshold crossing peaks as of this morning (PST).

January - 2018

~    1st:  37cpm peak at 15:16 hours (always UCT) (isolated).
~    2nd: 33cpm peak at 21:04 hours (isolated).
~    8th:  No other threshold crossing peaks as of this morning (PST).
~    8th:  34cpm peak at 21:03 hours (isolated).
~    9th:  No threshold crossing peaks today, but between 08:00 and 16:00 hours (UTC) the average hit 117.8%!
            I'm not aware of any special reason for it. Here's a 2 day graph (Ctrl+ to enlarge the images.):

            --for which 15.61cpm equals "100%" (my station's 2-week baseline average 4 years ago). My steep roof sheltered, sealed, one meter above the ground, outdoor sensor only responds to gamma type and very hard beta radiation. For all I know, this elevated count period could be cosmic ("muons") in origin, or the 8 hour sleep period (midnight to 8am here) of a neighbor with a radioactive tracer in her blood.

~  14th:  36cpm peak at 06:13 hours (isolated).
~  25th:  33cpm peak at 11:12 hours (isolated).
~  31st:  No other threshold crossing peaks as of this morning (PST).


February - 2018

Unusually high 10 & 60 minute averages for February 18th-19th (Ctrl+ to enlarge the images.)

~  22nd:  35cpm peak at 17:35 hours (isolated).
~  28th:  No other threshold (33cpm) crossing peaks as of this morning (PST).


March - 2018

~ 12th: 34cpm peak at 17:13 hours (isolated).
~ 13th: 35cpm peak at 07:05 hours (isolated).
~ 17th: 33cpm peak at 10:25 hours (isolated).
~ 21st: 35cpm peak at 15:23 hours (isolated).
~ 23rd: 35cpm peak at 16:01 hours (isolated).
~ 24th: Normal looking graph today.
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).


April - 2018
~   4th: 34cpm peak at 22:45 hours UTC (isoated).
~ 15th: 35cpm peak at 05:17 hours (isolated).
~ 17th: 37cpm peak at 18:34 hours (isolated)
~ 24th: 34cpm peak at 08:13 hours (isolated)
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

May - 2018
~   4th: 33cpm peak at 23:48 hours UTC (isolated).
~ 14th: 34cpm peak at 13:34 hours UTC (isolated).
~ 21st: 34cpm peak at 07:48 hours UTC (isolated).
~ 24th: 33cpm peak at 12:16 hours UTC (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

June - 2018
~   6th: 33cpm peak at 10:52 hours UTC (isolated).
~   7th: 35cpm peak at 10:51 hours UTC (isolated).
~   9th: Posted this 24 hour average up-tick, following a long calm period.
            (Saved the normal looking 24 hour graph. Highest peak was 31cpm.)
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

July - 2018
~   7th: 33cpm peak at 02:11 hours UTC (isolated)
~   7th: 33cpm peak at 18:09 hours UTC (isolated)
~ 12th: through 18th: Monitoring has been continuous and no peaks have been missed, but I averaged over
                                    periods of 2 days and then 3 days --due to distractions and my increasing forgetfulness.
~ 21st: 35cpm peak at 21:28 hours UTC (isolated)
~ 31st: 33cpm peak at 10:21 hours UTC (isolated)
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

August - 2018
~   2nd: 33cpm peak at 04:01 hours UTC (isolated)
~   2nd: 33cpm peak at 23:56 hours UTC (isolated)

~   9th through to the 12th: * This gap was due to my having been injected with the radioactive tracer technetium-99m, for the procedure: "myocardial perfusion imaging", which (by calculating backwards from my later radiation counts) initially rendered me something like 15 times higher than background --11 feet distant. (Six hours later, with me seated 11 feet from my outside monitoring station, it was tallying 7.4x background. Due to the isotope being distributed throughout my body, the "inverse square law" doesn't apply at close range, but at roughly 3 hours, the count hit 1800cpm [115x background] when I was standing near the sensor's housing.)

* That said, there are "tens of millions" such procedures performed each year (see Wikipedia's Tc-99m articles) with an over-all casualty rate of 1 cancer or leukemia per 1000 patients. Technetium-99m emits (some sources say "only") gamma at 0.142 MeV (142 KeV), plus (other sources say) loses 12% of its mass via beta decay at a similar low energy. The injected 99m pretty much decays into plain technetium-99 in a day or two, which in turn decays by way of low energy beta (electron) emission --but that takes 211,000 years, so its dose rate^ is pretty low --plus: the biological half-life for both 99m and 99 is only 24 hours.

* And that said: The radiation I've sustained from my particular procedure is (per the Wiki) the equivalent of 94 (2 view) chest X-rays (!!) --and my wife gets a second-hand exposure at 1/10th of a chest X-ray, so I now have a (linear exposure theory extrapolated) statistical 1 in 5000 lifetime risk of developing a solid cancer or leukemia --but it's actually much less, since I'm already 75 years old and (statistically) almost dead anyway --but maybe it's more --after a lifetime's accumulation of such risk factors (radioactive and otherwise).

* I have to wonder about all the technetium-99 which passes through the bodies of "tens of millions" of patients and out into the environment.

^ Since the indicated dose rates of Geiger counters are typically calibrated with a standard cesium-137 source (the intermediary decay product of Barium-137m is what actually radiates), perhaps the 142 keV gamma rays of technetium-99m are a lot less ionizing and less biologically impactful than are the 662 keV gamma rays/photons of Cs-137. I believe we report dose units of micro-REMs (uR) and Sieverts (uSv) to each other for convenience, since they're cross-Geiger-counter comparable --even though most folks take the indicated "dose" seriously.

~ 13th: 33cpm peak at 01:30 hours UTC (isolated).
~ 16th: 34cpm peak at 00:17 hours UTC (isolated).
~ 20th: 33cpm peak at 15:11 hours UTC (isolated).
~ 20th: 33cpm peak at 21:19 hours UTC (isolated).
~ 25th: 33cpm peak at 19:22 hours UTC (isolated).
~ 27th: A G3 solar sourced magnetic storm today, but to no apparent affect.
~ 30th: 33cpm peak at 01:15 hours UTC (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).


September - 2018

~  5th: My outside station count did a whoop-dee-doo at 20:38 hours UTC, hitting a 50cpm peak at about 22:40 hours. Judging by the sudden rise and the rate of decay, this is about a Technetium-99m dosed neighbor coming home from his/her appointment. I saw nothing special to the north or south on the Radiation Network map.


Sorry for the 12 hour UTC format --and for those time base intervals. (Ctrl+ to enlarge the images.)

~   8th: 33cpm peak at 06:08 hours UTC (isolated).
~ 13th: 33cpm peak at 21:21 hours UTC (isolated).
~ 16th: 36cpm peak at 22:23 hours UTC (isolated).
~ 18th: 33cpm peak at 06:43 hours UTC (isolated).
~ 25th: 34cpm peak at 02:43 hours UTC (isolated).
~ 29th: 33cpm peak at 20:29 hours UTC (isolated).
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).


October - 2018
~   5th: This is the middle of 3 days averaged. (Events and obligations come up and I forget.) (75 years old.)
~   6th: 37cpm peak at 11:01 hours UTC (Quite isolated --to a single minute).
~   9th: 33cpm peak at 18:11 hours UTC (isoated).
~ 12th: 37cpm peak at 14:58 hours UTC (isolated --1 minute only).
~ 12th: 33cpm peak at 19:30 hours UTC (isolated).
~ 13th: 34cpm peak at 12:04 hours UTC (isolated).
~ 18th: Found my counter program shut down --must have forgotten to restart it.
~ 19th: 33cpm peak at 16:45 hours UTC (isolated).
~ 23rd: 33cpm peak at 02:43 hours UTC (isolated).
~ 27th: Early graph post, due to the lack of an expected "background" count increase.
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

November - 2018
~   1st: 33cpm peak at 15:13 hours UTC (isolated).
~   4th: 35cpm peak at 10:46 hours UTC (isolated).
~ 13th: 34cpm peak at about 21:00 hours UTC (isolated).
~ 14th: 38cpm peak at 05:01 hours UTC (isolated).
~ 16th through 24th: Highest 24 hour averages since January-February and highest build-up/decay type
                                  24 hour averages in years. Peter Daley (who operates the Sunshine Coast station)
                                  showed our e-group weather maps which indicate this event is surely due to a smoke
                                  incursion from California's wild fires (well south of my station's Oregon location).
                                  I'm re-calibrating my inside station to corroborate my outside station's excursions.
~ 29th: 34cpm peak at 15:17 hours UTC (isolated).
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

December - 2018
~   8th: 33cpm peak at 04:08 hours UTC (isolated).
~ 15th: 34cpm peak at 11:25 hours UTC (isolated).
~ 18th: 34cpm peak at 17:21 hours UTC (isolated).
~ 21st: 33cpm peak at 20:49 hours UTC (isolated).
~ 27th: 33cpm peak at 01:40 hours UTC (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

January - 2019
~ 14th: 33cpm peak at 06:11 hours UTC (isolated).
~ 14th: 34cpm peak at 19:34 hours UTC (isolated).
~ 24th: 33cpm peak at 00:34 hours UTC (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

February - 2019

The day graph from 2/2/2019 to 2/3/2019 (Ctrl+ to enlarge the images.)
(Sorry for the 12 hour UTC format --and those inscrutable time base intervals.)
~   3rd: 33cpm peak at about 04:00 hours UTC (isolated with soft build-up).
~   3rd: 33cpm peak at 04:58 hours UTC (isolated with soft build-up).
~   4th: 33cpm peak at 07:47 hours UTC (isolated with soft build-up).
~ 22nd: 34cpm peak at 03:26 hours UTC (isolated).
~ 28th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

March - 2019
~ 31st: There's a monitoring station for smoke from regional forest fires and slash burns that's only 1.6 miles from our outside radiation monitoring station. It's on the Web and reports 2.5 micron size particulates --as estimated micrograms per cubic meter of air. Maintained by a consortium of volunteers, it posts hourly as well as daily averages. I've graphed it until the 25th. There doesn't appear to be much correlation at these low levels. No doubt we'll see some future mutual peaks --and I'll try to access earlier smoke data as well. The smoke station is at about 285 feet (above MSL).  My station's at 93 feet.

March - 2019 (continued)
~   3rd: 33cpm peak at 23:30 hours UTC (isolated, with a 31cpm leading spike).
~   6th: 33cpm peak at 16:09 hours UTC (isolated, but a busy graph today).
~ 22nd: 33cpm peak at 07:37 hours UTC (isolated, but a busy^ graph today).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

April - 2019
~ 17th: Cleaned bad connections --after losing the daily total count.
~ 20th: 33cpm peak at 03:01 hours (UTC) (isolated).
~ 25-26th: Forgot and let the count run for 2 days. Nothing lost (except daily resolution).
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

May - 2019
~   3rd: 33cpm peak at (about) 09:00 hours (all UTC) (isolated).
~   3rd: 35cpm peak at 13:51 hours (isolated).
~   4th: 33cpm peak at 10:05 hours (isolated).
~   4th: 35cpm peak at 11:01 hours (isolated).
~   6th: 33cpm peak at 11:31 hours (isolated).
~ 11th: 34cpm peak at 17:25 hours (isolated).
~ 14th: 36cpm peak at 11:56 hours (isolated).
~ 13th through 16th: Looks like a mild build-up. It started raining again, NASA Space Weather speaks of incoming coronal mass ejections from the Sun, the wind is from the north, a smoke/particulate station just 1.6 miles distant looks normal and about half of what it was back in March. (I was waiting for such an increase in order to compare the smoke graph and to standardize how to present it here.)

Both displays are as of the 16th of May.

~ 16th: 33cpm peak at 11:30 hours UTC (isolated). (Saved display screen due to mild build-up.)
~ 24th: 36cpm peak at 13:21 hours (isolated).
~ 26th: 33cpm peak at 05:31 hours (isolated).
~ 30th: 33cpm peak at 16:54 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).


June - 2019
~   6th: 35cpm peak at 15:08 hours UTC (isolated).
~   7th: 33cpm peak at 10:57 hours (isolated).
~ 11th: 33cpm peak at 21:11 hours (isolated).
~ 24th: The Sun has been very quiet --no spots.
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

July - 2019
~   7th: 34cpm peak at 05:22 hours UTC (isolated).
~   8th: 35cpm peak at 01:59 hours (isolated).
~ 20th: 33cpm peak at 12:20 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

August - 2019
~  3rd: 33cpm peak at 04:03 hours UTC (isolated).
~ 12th: 34cpm peak at 03:42 hours (isolated).
~ 19th: 33cpm peak at 07:08 hours (isolated).
~ 27th: 35cpm peak at 14:17 hours (isolated).
~ 31st: 33cpm peak at 12:24 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

September - 2019

~ Due to distractions, I several times let the counter run on for 2 or 3 days. No data or peaks were lost.
~ 15th: 33cpm peak at 18:44 hours UTC (isolated).
~ 16th: 37cpm peak at 07:03 hours (isolated).
~ 18th: 34cpm peak at 10:13 hours (isolated).
~ 21st: 33cpm peak at 21:27 hours (isolated).
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).


October - 2019

~ There are runs of more than one day, but no data or peaks were lost. Fortunately, the counts have been calm.
~  8th: 35cpm peak at 06:55 hours UTC (isolated).
~  9th: 33cpm peak at 06:27 hours (isolated).
~ 11th: 33cpm peak at 17:19 hours (isolated).
~ 23rd: 34cpm peak at 00:01 hours (isolated).
~ 11/01: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).


November - 2019
~   7th: 34cpm peak at 01:38 hours UTC (isolated).
~   9th: 34cpm peak at 17:23 hours (isolated).
~ 13th: Power failure + backup battery failure = no data today.
~ 18th: 34cpm peak at 00:37 hours (isolated).
~ 27th: I'm guessing this is about the California wild fires. I tried to access a nearby smoke monitoring station but data for these past two days has been lost. (They seem to lose a lot of data.) There were no threshold passing peaks. Here's the daily Geigergraph record:

Minute by minute Geigergraph for 11/27-28 (click to enlarge)
~ 29th: 33cpm peak at 05:15 hours (isolated).
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

December - 2019
~ 10th: Unusually high 39cpm peak at 00:37 hours UTC (quite isolated).
~ 13th: 34cpm peak at 16:11 hours (isolated).
~ 26th: 33cpm peak at 20:54 hours (isolated).
~ 29th: 33cpm peak at 22:43 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

January - 2020
~  2nd: 33cpm peak at  02:26 hours UTC (isolated).
~ 21st: 34cpm peak at 06:37 hours (isolated).
~ 23rd: 33cpm peak at 17:55 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

February - 2020
~ 28th: 33cpm peak at 02:43 hours UTC (isolated).
~ 29th: 35cpm peak at 10:40 hours (isolated).
~ 29th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

March - 2020
~ 29th: 33cpm peak at 22:55 hours UTC (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).


April - 2020
~  3rd: 33cpm peak at 04:20 hours UTC (isolated).
~  3rd: See the air sample decay graph.
~  9th: 34cpm peak at 16:17 hours (isolated).
~ 16th: 33cpm peak at 12:47 hours (isolated).
~ 17th: 33cpm peak at 00:44 hours (isolated).
~ 18th: Due to statistical count variations and/or actual count variations, both in the
        running base line and the draw filter counts (note the 10 minute average trace
        below), there's no recognizable decay curve at this low level.
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

The 4/18 air draw P1-P4 counts spanned the last hour of this (outside station) graph (click to enlarge)

May - 2020
~ 15th: 33cpm peak at 10:46 hours (isolated).
~ 26th: 34cpm peak at 03:15 hours (isolated).
~ 29th: 36cpm peak at 04:33 hours (isolated).
~ 30th: 33cpm peak at 03:28 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this evening (PST/PDT).

June - 2020
~ 19th: 34cpm peak at 14:21 hours (isolated).
~ 30th: 34cpm peak at 11:52 hours (isolated).
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

July - 2020
~  3rd: 33cpm peak at 10:53 hours (all UTC) (isolated).
~ 10th: 33cpm peak at 01:04 hours (isolated).
~ 11th: 34cpm peak at 03:58 hours (isolated).
~ 16th: 35cpm peak at 13:25 hours (isolated).
~ 17th: 37cpm peak at 10:09 hours (isolated) --no build-up).
~ 28th: 33cpm peak at 10:04 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this evening (PST/PDT).

August - 2020
~  4th: 35cpm peak at 15:14 hours (all UTC) (isolated).
~ 16th: Saved a normal looking (if somewhat high day's average) screen capture.
~ 22nd: 33cpm peak at 08:41 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

September - 2020
~  1st: 35cpm peak at 12:15 hours (all UTC) (isolated).
~  8th: Smoke from Oregon's forest fires blotted out the Sun at local noon, seemingly replaced by fog (and
        smoke) on the morning of the 12th (as I type this note). Although an air draw filter (at 00:30 hours
        on the 10th - UTC) showed a significant count (with an unusual decay curve/step), my daily 24 hour
        averages were barely affected (implying mutations and beta in the filter --see the blue P2 & P5 dots).
        I washed the exterior of the outside station's housing on the morning of the 11th, but the subsequent
        count downturn doesn'tseem statistically significant.
~ 10th: 33cpm peak at 06:11 hours (isolated).
~ 11th: 33cpm peak at 16:17 hours (isolated).
~ 13th: This morning's count was running at 108%, so I did another air draw, getting a high (but not record)
        count from the filter and a decay curve more typical of radon daughters. (No rain here for a long time,
        and little or no sunshine on the sand and soil --so it has to be coming in with the smoke --sourced
        100 miles away, where the radiation must be pretty high.) The day's peak minute count was only 30.
        It's my guess that our intense Oregon fires are liberating radon from forest floors.
~ 17th: 33cpm peak at 09:32 hours (isolated).
~ 19th: 35cpm peak at 07:53 hours (isolated). Smoke has cleard with rain.
~ 28th: 34cpm peak at 09:28 hours (isolated).
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

October - 2020
~  2nd: 33cpm peak at 14:53 hours (isolated) (all UTC).
~ 16th: Apologies! --I made a 16th day update graph but didn't post it this month, (Getting old.)
~ 27th: 34cpm peak at 14:40 hours (isolated).
~ 31st: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).


November - 2020

~ November 2nd: I did a "base line" beach wander today at 22:15 hours UTC. These wanders/walks will only be on Bastendorff Beach (from here on), will follow a recent high tide line and prominent secondary froth lines, in order to audibly detect any discrete, gamma emitting hot particles such as "fuel fleas". (I've yet to find any.) These will be 10 minute walks (per the Geiger counter's internal timer) at about 30 inches above the sand. The count was 96% of normal today.

(Click to enlarge)
~ November 2nd: It became clear, when looking at my 11/2 to 11/3 graph, that there was a minor event centered on 18:00 hours UTC (late morning -PST- of 11/2 here, displayed as "6pm" UTC on this graph). The 10 minute and 60 minute averages reached 20cpm (128% of normal, that small circle on the November graph), then took about 90 minutes to settle down (and in plenty of time for my "beach wander"). Never the less/more, the 11/2-11/3 24 hour average ended up at only 103.2%. (The previous 24 hours averaged to 104.9%.) (I might have missed previous such events/waves. I have no idea of its significance, or even of what I'm counting.)

~  3rd: 34cpm peak at 22:24 hours (isolated) (all UTC).
~  9th: 33cpm peak at 14:59 hours (isolated).
~ 21st: 34cpm peak at 19:47 houea (isolated).
~ 23rd: 37cpm peak at 01:19 hours (isolated).
~ 29th: 34cpm peak at 18:34 hours (isolated).
~ 30th: No other threshold (33cpm) crossing peaks as of this morning (PST/PDT).

(See also: current/recent monitoring)


Notes and Comments

* January 31st, 2020: Japan has decided to slowly drain the vast storage of radioactively contaminated water --into the ocean. If the "linear" theory of radiation induced casualties is correct, slow or fast release (over a wide range of rates) will make little difference to the collective health of peoples who harvest sea food. a kilogram of a radio nuclide, dilluted into a million kilograms of water will damage/sicken people at rate "X", while the same kilogram, dilluted into 100 million kilograms of water --will damage 100 times as many people at the rate of 1/100th X.

March 31st update: After thinking on it (the above paragraph), the more concentrated release might damage fewer people, do to "wasting" much of the contaminant as over-kill. It's just the news headlines which would look worse.

* The May 18, 2017 edition of Space Weather (use their archives retrieval utility, top right of page) carries an article describing the recent discovery that very low frequency radio communications to our nuclear submarine fleet also resonate the Earth's magnetosphere, forming a belt around the Earth. That belt appears to be offering protection to satellites (and space farers?) against "killer electrons" --presumably born of primary cosmic rays. That outcome is an accidental byproduct of (what I gather to be) near 24/7 radio transmissions since the 1960s, so we might not have ever been able to study the Earth's normal deployment of its magnetic field and radiation belts.

What I want to know: if high energy electrons (beta radiation) can be "killers" of space electronics, then tell me more about muons --which carry the same negative charge, move at relativistic speed, are over 200 times more massive than electrons, might constitute half of our normal "background radiation" near sea level, and much more at higher altitudes. How is it that the health-physics people assign muons the same biological impact as gamma and X-rays? (Somehow, they're alleged to shed/impact very little energy per foot of travel.)

* It looks like 1800 tons of "spent" fuel rods are going to be sequestered indefinitely a little more than 100 feet back from the high tide line as the San Onofre nuclear power plant in California gets fully decommissioned. At least it will be out of the poorly protected pools, but this stuff must be kept safe for thousands of years, since spent fuel is a far worse radioactive hazard than fresh rods. If I read the news correctly, the outer containers, made of 5/8" stainless steel (instead of the European standard of 20 inches), will only be half buried --perhaps due to the water table. (Stainless steel deteriorates in a watery environment, which is why maritime hardware is made of bronze.) Be my guess that, with the rising sea level, corrosion will make the containers and their contents un-moveable, long before a permanent nuclear waste repository has been completed. Are property values within a 50 mile radius already dropping?

* An item --from the Bulletin of the Atomic Scientists. (But they missed citing the Fukushima detonations!)

* For those of you following my graphs, feel free to email me when an item on this page is out of place, out of date, gone missing or wrong. I normally update my graphs at 8 day intervals or within 24 hours of an event.

* My (steep slope roof) sheltered, sealed and desiccated outside monitoring station humbly emulates those used in Germany. While I have a bench setup for the consistent (if not accurate) reading of beta and gamma from samples and air filters, I attempt to avoid counting beta (and I can't count alpha) radiation with my outside station or my "walks", since that would only serve to inconsistently mess with the totals --having more to do with wind and rainfall than any presumed artificial radiation content. (If my outside count goes up, I'll do some air readings again.)

The "Preamble" to this page:

* 11/03/2021 up/backdate: Here are links to "what are we counting" discussions elsewhere which might interest you:

* (December 3, 2014)  in a 0.10 uSv/hr field, the long term average of my GMC-200's M4011 tube comes out to about an even 16cpm --same as the SBM-20 tube in my Radex-1503. The less-than-optimized SBM-20 that I retrofitted into a Medcom "Inspector" clicks at about 15cpm. The Inspector's original LND-7317 pancake tube would click at about 35cpm in that same field.
> https://www.gqelectronicsllc.com/forum/topic.asp?TOPIC_ID=4099

* (December 13, 2014) Some say that even at sea level (MSL), about half of my count is muons. (Others say that muons hardly register on a standard Geiger counter.) With a high energy capable scintillator, the density runs about 1/cm^2/minute –which pencils out close to MSL background, given the profile of common G-M tubes. / G-M tube manufacturers’ specifications commonly cite –what I’d call a “noise level”, but what they call “own”, inherent, “self”, or “shielded” background levels that approach or exceed commonly logged MSL background radiation
> https://www.uradmonitor.com/topic/what-the-heck-are-we-counting/

* (January 21, 2015) We get a noise figure of "0.2cps" = 12cpm (which no one wants to talk about), but nowhere do we see the stated gamma sensitivity. I see companies which use LND G-M tubes stating sensitivity in a calibrated 1000uR/hr field of cesium-137 radiation --which lobs the count way above any contested levels of internal noise and/or local "background" levels. Those of us doing low level background monitoring then interpret (say) a spec of 3500cpm at 1000uR/hr --to meaningfully indicate 10 uR/hr (0.10 uSv/hr) at 35cpm.
> https://www.gqelectronicsllc.com/forum/topic.asp?TOPIC_ID=3664

* (January 2, 2017) I measured background (18.1 CPM here in Germany, measured over 1 day) and then tried to reduce background by shielding the device. Thick layers of cardboard, a tin box, a lead bag (from the times when you had to get real photographic films through the airport scanners). Not much success;  the background barely changed.
> https://www.gqelectronicsllc.com/forum/topic.asp?TOPIC_ID=4421

(April 30, 2020) I am wondering if the GMC-600 Plus firmware/calibration routine accounts for the internal noise / counts of the GM tube? / The more sensitive the tube is, the higher the noise is going to be. For an example - the GM tube used in GMC-600Plus is LND 7317. LND Inc specifies this tube as max of 30 CPM under heavy shielding conditions (50mm Lead + 3mm Aluminum).
> https://www.gqelectronicsllc.com/forum/topic.asp?TOPIC_ID=9062

* 6/12/2019 update: This section asks: "just what is it that I'm counting?" --and I'm still not sure. Recently, the Sun entered a quiet period --perhaps to become an extended "minimum" (the spot count and flaring goes to zero). As a consequence, high altitude cosmogenic radiation counts (including neutrons) have gone up --since the solar wind has diminished --along with its ability to run interference for us against in-coming primary radiation (particles, protons, whatever). YET: my counts have not gone up --which you'd expect if the cosmogenic (muon) count is more significant.

On the other hand, many marine studies, and studies which rely upon the radiation stopping power of the ocean's deep --indicate that "background" gamma radiation (at least with high quality scintilators) is largely cosmogenic/atmospheric --which agrees with my own subersion experiments. (The nut of my efforts: I got a healthy background count with my Geiger counter suspended just above our bay --so earth wasn't my source, but the count was significantly reduced when submerged [well clear of the bottom].)

Here's a professionally executed example: "Environmental Gamma-Ray Observation in Deep Sea" by JAMSTEC (Japan Marine Science and Technology Center, Japan Agency for Marine-Earth Science and Technology), published in 2012 --a PDF that you can Google up.

I don't know how much is contributed by the internal noise of my (very affordable) Geiger-Mueller tube (all the spec sheets suggest much noise). Perhaps there are significant contamination/noise differences from tube to tube --up to a spec sheet maximum, which would become evident when comparing low level "background" counts between G-M tube samples.

* 10/27/2018 update: A 5 year-long string of inquiries^, tests, monitoring methods, 3 Geiger counters, discussions and reading parts of Glenn F. Knoll's book: RadiationDetectionand Measurement --at first led me to subtracting an apparent "noise" component from my counts, only to finally go back to whole count averages.

* I became satisfied that the G-M tube noise component (what remains after shielding out all that one can, which is about half of a normal "10 uR/hr" count here) --is largely due to secondaries and tertiaries from cosmic (sky/space) radiation.

** However: Student balloon runs (October - 2018) reported (at Spaceweather.com) 20% and higher increases in cosmogenic radiation at stratospheric altitudes --and I didn't see an increase in my station counts.

* I've read that the cosmogenic stuff is about 80% muons (near mean sea level --I'm at MSL+90 feet here) --to which health-physics assigns the same biological impact as ordinary gamma rays (despite their speed, charge and mass). Counting efficiency is near 100% for higher energy beta (electrons), so I'd expect muons, which carry the same charge plus they have 200x the mass, would also count well --but they're said to shed little ionizing energy as they travel --at relativistic speeds.

* What this comes down to: all I know for sure is *click* *click* *click* and how much my click count rate varies.

* Note --that my counts have been in the +/-5% range for years --and what does that tell us?

* Earlier, I revised the several (noise subtracted) 2016 graphs I'd made, bringing them in line with the whole count graphs of recent years and all graphs since.

* I've also dispensed with specifying "standard deviation" and multiples/probabilities there-of. The count is made up of disparate components and I just don't know how valid it is to base that on a simple, total count.

** My thanks and a shout-out to Dr. Martin Bleher of Germany's Federal Office for Radiation Protection (Bundesamt für Strahlenschutz), who addressed my long standing questions. Dr. Bleher could, of course, only speculate on their own G-M tube "noise" components, and although he didn't directly state as much, I gathered that they log all the clicks, which are then presented to the public as so many (current) uSv/hr "dose rate" units --without distinctions or speculation as to the actual components. (I wrote a polite note back to him with these inferences of mine, which he has not corrected.)

* I've been aware of G-M tube noise specifications for years, but they've always been ambiguously given as a (rather hefty) upper limit (when shielded with 50mm of lab lead --perhaps with some interior aluminum as well to soak up "bremsstrahlung" secondaries). I previously couldn't get satisfactory answers about noise from those I've contacted, nor did I trust my own methods for detecting "noise" (which appeared to be quite high in my tests as well).

    ~ I suspected there was more to "noise" than the lead shielded remainder value --and more to it than internal G-M tube contamination, because I got another 22% reduction by submerging a Geiger counter to a depth of 2 meters here in Coos Bay's bay. (I used 8 pounds of lead in my simple pressure vessel --not intended as shielding, but for ballast, for whatever radioactive contamination my cheap lead shot might have contributed^.)

^ Technicians doing professional lab work use only quality, clean, radioactively quiet lead bricks for building their "lead castles" --into which their samples and ultra sensitive scintillator probes are placed. Lead shot (for loading shotgun shells), on the other hand, is surely the worst grade of lead (blended with antimony) that you could use --but: it's cheap, widely available, packs well, and (in thick plastic "freezer" bags) is easy to work with. (Be sure to buy it all in the same pellet size, at the same place, and at the same time, such that it's homogenous and always packs the same --for consistently effective shielding.) Perhaps lead shot is good enough for shielding the amateur's G-M tube.


My outside Home Station --loaded up with lead shot for a "noise" test.

* My noise inquiries entailed postal letters, email and web site feedback utilities. I contacted several "ask a scientist" venues (including Firmi Labs, which sent me a nice response), the Nuclear Physics Department of the University of California Berkeley campus (which invites such questions, but no response after 4 tries), Bundesamt für Strahlenschutz (a nice response years ago, and now again [thanks!]), two university campuses here in Oregon (one very nice response from a department secretary), several Geiger counter manufacturers and dealers, and (of course) the groups and "web people" which the monitoring community is close to: Safecast, Radiation Network, Fairewinds, Energy News, "Anti-Proton", Citizen Scientist League, Robert Hart ("Hardhack"), LND (indirectly), Aware Electronics, and others --with several good (if somewhat contradictory) responses.

(I'll try to update what follows, but will leave the original date when it seems best to do so.)

* (2016) I'm continuing with the daily monitoring of 1 minute counts and 10 minute running average counts, archiving any unusual daily automatic graphs (via an off-line, beta edition of GeigerGraph-5). Each morning I look at a graph display to see if there've been significant departures or trends away from my station's (January 2014) base line average of 15.77cpm.

    ~ These past two years I went from 33cpm to 32cpm and back up to 33cpm again --for the 1 minute "alert level" that I've set into my data logging. I visually (and more sensitively) look for trends and my 10 minute alert level (now 22cpm). Since there's a "Poisson distribution" of counts around my station's long term average,one might expect to see isolated, one minute long, 32cpm counts to occur every day by random chance alone. (although I no longer (as of 2016) cite graph excursions as so many standard deviations/"sigma", I've done the mean/variance calculations for a large number of counts and their distribution agreed fairly well with the statistical Poisson assumption.)

** As of October 10th, 2015 --and being ever so weary of accommodating DST changes to my radiation and astronomy date stamps, I standardized my computers to "UTC": "Co-ordinated Universal Time", which (I think) is the same as GMT minus any DST happy horse-shit. (All USA clocks should run on UTC or some other single time standard --as they did across the old Soviet Union.)

General reminders:

* My radiation charts are updated at 8 day intervals, or within 24 hours of an event.

* Per my corrections of January, 2014, "100%" was set equal to an outside station average of 15.77cpm (using a glass M4011 G-M tube), then corrected again to 15.61cpm (due to a net 1% long term contradiction between the Spread Sheet and the "Report" logging of the software I'm using). It works out that the graphs' continuity has not been affected.

* This "100%" represents the long term averaged count for my outside station. It would correspond to (about) 36cpm from a typical, "pancake tube" (LND-7317) equipped Geiger Counter (say: a Medcom brand "Inspector") --placed in a steep roofed, plastic sealed shelter, at a meter off the local ground^. It also represents about 16cpm from an LND-712 equipped Geiger counter, or an indicated "10uR/hr" (10 micro-Rem per hour), or "0.10 uSv/hr" (micro-Sieverts per hour) --from any Geiger counter with a (meaningless, but roughly cross-Geiger counter equalizing) indicated "dose" display.

^ I've several times  compared long period averages between my outside station and a test bed location in my office, getting the same results (meaning: they were within an expected narrow range of statistical departure). Were we to suffer significant fall-out from a radiological event, no doubt the steep roof of the outside station's shelter would shed particles faster than the roof of our house, but both would provide an alert.

* There's pretty good agreement among monitoring stations along the west coast of the United States, per this June, 2017 "uRAD" monitoring map:


(Ctrl+ to enlarge this image.)
(No: I don't know why the circles are differently sized.)

* Note that typical "survey" Geiger counters and their Geiger-Mueller tubes are commonly calibrated and/or rated at 1000 uR/hr (using a cesium-137 source at a specified distance), and were originally intended for such high level readings as might be encountered during triage after a radiological accident or attack. We (in the monitoring community) use these Geiger counters at background levels because they're affordable and practical (if used methodically). Again: their "dose" indications would only be meaningful when reading Cs-137 contamination at a specified location --but: uR/hr and uSv/hr allows us to roughly compare readings between a diversity of such instruments (much as I'd prefer the station specific base line percentages that I'm using).

* So: what are we actually reading? By isolating a geiger counter in a meter-high, desiccated, gamma radiation transparent plastic housing, CPM (or "dose") readings will hopefully be minimally affected by natural local or fall-out beta and alpha radiation --which should be separately attended to via the methodical (if however humble) readings of soil samples and forced air filters. That being the case, and at such low background levels as I've been reporting for 5+ years, perhaps over half of the counts are due to  secondaries and tertiaries from cosmic/sky  radiation --which might be mostly "muons" --which are some 200x the mass of electrons and carry the same charge (ouch!) (ouch?).


(The following was partially updated on 7/31/2016)
Graphing modes compared^

Three graphs from the same data (above)

^Since October of 2012 my custom graphs have been rendered with the excellent (and free) "ZGrapher" program.

Statistically expected peaks: Here we see minute-by-minute counts (red) and 10 minute averages (black), based on but altered (for more visual clarity) from an early beta version of GeigerGraph-5.x. What you're looking at is statistical noise --rather like counting how many people happen to be passing through the gate into your county fair, per each minute of the day. The more people and the longer the period counted, the closer your people graph line would settle down to a longer term average. (My station's gamma activity has a very long term average of 15.61cpm.)

* For our radiation counts, we'd expect them to be within the square root of the total count --about 68% of the time (that is to say: within plus or minus one "standard deviation"^ for 68% of the time), which total count you'd then divide by the number of minutes in the period counted --for the average CPM. Notice how the red line excursions appear to be something like 3 times wider than the 10 minute averages. The square root of 10 is about 3.16.

^ However: I've stopped referencing standard deviations (or so many "sigma") since gathering that these counts are made up of very different components ("NORM", cosmogenic, plus any "fall out" that we worry about). All I know for sure are my count totals, what I'm using for Geiger counters, and how/where they're located. I strongly suspect that I'm not alone in this and that very few people have a good handle on what drives their low level "background" counts.

* The several kinds of averaged graphs I've generated (manually and with graphing programs) all look different. I don't like any of them, so I might as well stay with what I've been doing (takes 5 manual operations), despite its tendency to miss events and produce statistical artifacts. Again: I see the maximum CPM for each day, I investigate the spread sheet and report on those which reach 33cpm or higher --so as not to miss anything egregious.

* 33cpm might seem rather high (4.4 "deviations" --from whatever) --but there are 43,500 minutes counted each month, and it's turning out there's (seemingly) about a 1 in 10,000 chance of a count running that high on the (valid or not) basis of the above described statistical noise. Usually, I find that in the 10 minute period surrounding such an event, the peak is isolated --and that the period's average isn't otherwise elevated.

* Never mind the oddly pointy and square topped shapes of the 10 minute graph line --per:


Graph Resolution
* Some of the available Geiger counter vendor graphing programs only offer 1cpm resolution, which results in that square and saw tooth wave appearance. My long term averaging and the situation here on the coast of Oregon (atypically calm?) are such that my graphs require at least 1/10th CPM resolution (I go 1/100th) in order to make out trends and to discern apparent spikes/dips from among the "statistical noise" ("wiggle", "grass", "Poisson distribution") which is always present.

* Try to avoid line graph displays which attempt to pretty-fy the results with such as 3-D effects, gradient color backgrounds, garishly colored fat lines and grids. Simple, jumpy, black-on-white radiation graphs are hard enough to interpret as it is.

Here's an illustration of the radon decay chain:
Normally, I filtered out the alpha (before my Medcom "Inspector's G-M tube went flat), so those lead-214 and bismuth-214 components melded to give a typical half-life of about 40 minutes (which varied a bit, depending on how long I waited to time it). When I use to read the alpha as well, however, the 40 minute decay went down to 29% of the initial CPM (again: using my Medcom "Inspector" Geiger counter).
Air Sampling:

* Originally, I used this Oreck vacuum cleaner (from our Goodwill Store) to
pull about 20 cubic meters of air through a 2 inch (exposed) 3M brand N95 filter patch in one hour.
(Note that 3/8 inch bypass hole, such that the vacuum's motor gets enough air to not over-heat.)
4/1/2020 update: This is the filter I used earlier. It measured 1-3/4" diameter ( 1-1/32" exposed to air flow). At left is the filter unit: a standard 1 inch PVC union fitting (I now use a 2 incher). Next is the assembled filter --about to get its weather head. Finally we see the filter/intake as it was originally located high above the porch rain gutter, but now it's only 26 inches higher (and 115 inches above ground level, measured to the bottom of the weather head), so as to survive our winter storms. (It's thanks to James Hollen for that plastic pipe union idea.) My filters were cut from face masks, so to keep them from humping up in the test well/chamber (imaged just below), I cut them down after the air draw to just the exposed diameter.

* Given the high demand/need for N95 masks now (re: the Covid-19 pandemic), I've offered my remaining N95 masks to a local clinic and am considering coffee filters. They're sold cheaply: 200 in a package. I've seen them rated as passing up to 15 microns. Looking at a Melitta brand "Super Premium", "Natural Brown basket filter, I see a sparse scattering of holes up to 36 microns, but nearly all of this paper fabric has much smaller pores, mostly just a few microns or less. I don't think the wee bit of 15 to 36 micron bypass matters, since I'm not trying to protect anything. I just want to catch some of the finer stuff and put it under a Geiger counter.

* In my case --counting only gamma and hard beta, I could sandwich two coffee filters together and be confident of micron level filtering --but (again) I'd have 99% plus micron level catching with a single layer. We'll see if I need double thickness for strength.

* 4/4/2020: Single thickness coffee filters are holding up fine. My initial air draw runs are producing a radon rate decay rate, as did my earlier work.

My test bed's well has shoulders to space samples and filters about 1/4 inch from the Geiger counter's screened window. The stepped aperture, 1/8" above the well floor, is for landing that aluminum plate. I could then subtract softer beta and alpha from the gross count. (But there's no longer any alpha detection. Despite my tender loving care, this Inspector's G-M tube failed at 14 months, so I retrofitted it with an SBM-20.)

* It's been a very long time since I've done air draws (due to my Geiger counter's pancake tube failure and having removed the Oreck vacuum to other purposes). Since I'm using coffee filters now, there's no need to recalibrate my air draw rate, as long as I keep my methods and minutes the same. Note that these decay rates are only for gamma and hard beta detection. Best I do morning air draws, simultaneous with the morning restart of my outside station's count --so I have a direct comparison over the first 20 minutes (along with the inside station background count).


The date should read: April 3rd, 2020

* Those big black dots suggest the variability range of my counts, due to the statistical randomness with which gamma photons happen to cross the little Geiger-Meuller tube in my detector-counter.

* At 31 hours the 4/3 filter count was at 93.1% (actual 20 minute average: 13.8cpm). At 32 hours: 101.6% / 15.1cpm. The virgin filter: 102.2% / 15.2cpm. The total counts were about 300 ("N"), so the expected "sigma" count distribution is something like +/-6%. (I'm not at all expert on this.)

~~~~~~~~~~~~~~~~~~~~~~
Checking Food
(4/26/2015 update)

* Peter Daley of Australia has made me aware that the risk of food contamination extends to serious, gamma emitting particles --aka: "hot particles" or "fuel fleas", for which a common Geiger counter could be a life saver. There are accounts of such particles to be found across the Internet, some of them active enough to affect a basic Geiger counter several feet away. (I'm talking a steady, penetrating, "this can of tuna for sure, not that one" count of hundreds or thousands of CPM.)

Thankfully, such occurrences are extremely rare. I've seen nothing but normal "backgrounds" here after 5+ years of daily monitoring (plus a neighbor who came home loaded with radiation from medical imaging). For a long while I made an effort to discretely carry a compact Geiger counter, especially when I went grocery shopping.

* If you decide to do that, I suggest minimal beeping/clicking and no theatrics. If the alarm sounds, switch straight to silent mode and mutter something about "damned cell phones" --but locate, and remove the hot item, mark it poisonous, write down (or photograph) any identification on the food item, what radiation reading at what distance, the manager's name, date, time --then attempt to interest the store's management and the hazmat crew of your local fire department.

* Unless you have a nearby lab to properly test it, I don't suggest that you purchase the food item, since it then becomes your responsibility --to competently and securely isolate the item, preserve and document its "chain of possession", and make certain that matters are properly attended to by the proper authorities.

* More on Peter Daley's resources, which include a volume of advice and links concerning radiation and food. Good starting points are:

The Food Lab: http://sccc.org.au/archives/2861

> http://sccc.org.au/wp-content/uploads/2012/06/How-to-set-up-a-home-or-community-food-testing-lab-for-radioactive-contamination.pdf

> http://technologypals.com.au/wp-content/uploads/2012/03/Using-a-Geiger-Counter-to-test-food-for-Radioactive-Contamination.pdf

* So: a Geiger counter does not, of course, have the sensitivity or discrimination to pronounce any food stuffs as being safe to eat. Neither can a Geiger counter condemn a food or beverage item --unless it's plenty hot --way hotter than the (mostly beta) CPMs you get in close proximity to (say) potassium chloride (dietary "salt substitute").

* Proper food monitoring requires spectrometry on the (often incidental) gamma radiation involved, which takes honorable equipment, handling methods, lab discipline, and learned, seasoned experience.

* Gamma emitters seem (to me) to be the only practical isotopes for an amateur with a Geiger counter to check for. Beta radiation is nearly all blocked by the moisture content and even the food's own bulk. When desiccated and/or thinly sliced, the available (and natural) potassium sourced beta count of many foods increases considerably, but that can swamp any count you're getting from serious traces of other polluting radio nuclides.

* Be very careful not to contaminate your Geiger counter when checking samples, when the air is not clean, and when at the beach (wind, spray, alluvial sand, salt air). Bagging it in a Ziploc is a good idea (but place a packet of freshly charged desiccant inside with it, or at least open and let the bag/counter breath after its back home, warmed up and safely stored).

Since 2017 there's been a new push to rehabilitate nuclear power. One of the leading designs (backed by Bill Gates) seeks to revive the 60 year-old notion of using high temperature, corrosive, flammable, molten sodium instead of water in the primary cooling/heat transfer loop. A sodium cooled test plant underwent our nation's first (and worst?) nuclear power meltdown in 1959. This probably comes as news to you because it was kept under wraps for 20 years. See:

> https://data.nbcstations.com/national/KNBC/la-nuclear-secret/
> https://www.commondreams.org/views/2019/07/13/60-years-largest-us-nuclear-accident-and-captured-federal-agencies


The Solar Flare Threat

January 5th, 2017 update: We made it through! (I think)

3/21/2015 update: Have we made it through the worst of this solar cycle? I sure hope so.

3/06/2014 update: Here's a *link* to a 3/4/2014 Wall Street Journal article by Rebecca Smith --which might display in full the first time you access it --but which might subsequently fade out. Apparently, this is the WSJ's new way to game us into subscribing), with more recent information on the availability of replacement EHV transformers. We do have a domestic manufacturer who can build the big ones (400 tons each! --similar to the largest stones in ancient megalith monuments), but it takes months to complete and deliver one. A recent delivery from an overseas source took about 2 years. (Hat tip to Majia for this information.)

3/15/2013:  Either the 2012-2013 solar maximum will be unexpectedly tepid, or it will come as a delayed "double peak". Watch the video at NASA Science News. Prevailing opinion favors a repeat of the double peaks we've seen in the last 2 solar cycles. (That video also reference a double peak during solar cycle #14 [early 1900s], but I didn't see one in the record that I looked at.)

If we do get a double peak, the second one might have us weathering a series of "X-Class" flares and coronal mass ejections ("CMEs"). Whether one of them smacks the Earth and shuts down some of our power grids is a game of "Russian roulette".



10/31/2016 update --thanks to: NOAA, ©2016 Spaceweather.com and Dr. Tony Phillips (w/o permission).

11/17/2016: Well: we got a "double peak", but we made it through anyway, and seem to be in the clear for some long while again. Never-the-less, I think --

It's vital that our political leaders understand and address the following points. (Good luck on getting through to them, but one recent presidential candidate pledged to phase out nuclear power: the Green Party's Dr. Jill Stein.)

* Nuclear power plants, despite that they might end up literally bursting with thermal energy, were designed such that they're unable to power their own cooling pumps --in the event that there's a local failure of the power grid. On-site diesel-electric backup power then takes over to run the pumps, controls and instrumentation.

* I know that's hard to believe, so rather than simply discounting my concerns here, please confirm it for yourself. Google on "station blackout". Newer designs use steam power to run turbine driven water pumps, but they still require electricity to open valves and turn those pumps on, which is supplied by only hours of battery power.

* Because the spent fuel pools (SFPs) were only meant to hold 1/4th or 1/8th of what was eventually crammed into them, there was no provision to supply them with emergency backup power at all.

* To be very clear about this: there was originally (and still?) no provision to connect the diesel backup generators to the SFP's cooling pumps --!! The plan was to simply let the water in the pool coast up --near to the boiling point (which might take as little as 24 hours), and to then replace boiled off water by means of manually deployed fire hoses. (Sweetjeez!)

* The SFPs are crammed with old fuel rod assemblies because there's no place to store nuclear wastes, and because the operator/owners of nuclear power plants are too cheap to use "dry cask storage".

* There are several deadly important things to understand about "spent" fuel pools and rod assemblies:

    ~ Their radioactivity is far more deadly than fresh nuclear fuel rods.

    ~ There's serious question as to whether their sometimes 40 year-old liners can stand the strain of boiling water.

    ~ If the zirconium cladding on the fuel rods gets hotter than 1800 degrees Fahrenheit, it oxidizes with steam and water, releasing explosive hydrogen. Above 2000F, the oxidation process turns into a furiously burning fire which destroys the rod, releasing its radioactive contents.

* As to keeping a reactor's containment cool after a shut-down, months of mechanically forced water cooling are required --but the U.S. Nuclear Regulatory Commission originally (pre-Fukushima) only required that nuclear power plants be independently capable of supplying diesel-electric backup power for 72 hours, plus 4 hours worth of battery backup power --to cover any delay in getting their diesel engines to turn over.

    ~ The Fukushima Daiichi power station reactors had 8 hours of battery backup power. They used every bit of it.

    ~ The NRC might have recently started upgrading that requirement to 8 hours of battery and more on-site diesel fuel. The recent near nuclear disaster at New Jersey's Salem nuclear power plant established that they had a store of 7 days worth of diesel fuel on hand.

    ~ While SFPs might require mechanical/forced cooling for a year, I don't know how long mechanical cooling is required to remove residual heat from a normally shut down, intact reactor in order to maintain "cold shutdown". The damaged reactors in Fukushima have required months of cooling.

    ~ Backup power will continue to be available at a nuclear power plant if more diesel fuel can be delivered to the power plant, if the diesel generators remain operable, and if operator personnel can be persuaded to remain at their posts. (The regular Fukushima crew initially fled, but was successfully ordered to return. The head of TEPCo has stated that, in the event of a fuel fire, he'd have no way of ordering his crews to face certain death in order to mitigate the situation.)

*** A report by the Oak Ridge National Laboratory stated that over the 40-year licensing term of a nuclear power plant, solar flare activity adds up to a 33 percent chance of it experiencing a long term power loss: a risk significantly greater than that of earthquakes and tsunamis --!

* Federal government studies have suggested that extreme solar flares could result in regional blackouts lasting months or even years, since critical power grid components like EHV (extremely high voltage) transformers are made in places like India and we have scant spares here in the United States. There are more than 300 aging, vulnerable EHV transformers in substations across this nation and the existing over-seas manufacturers of these transformers currently have a 3-year backlog of standing orders.

* A severe solar storm might destroy hundreds of transformers world-wide, leaving vast populations without water, sewers, hospitals, TV/radio broadcasts, fire and basic safety services. Military escorts would have to bring in fuel tankers through the ensuing chaos from our strategic reserves, since the pumps which normally transfer gasoline and diesel fuel wouldn't be operating, nor would refineries be making more.

* I understand that nothing material has been done to provide for the recovery of our power grid.

* As of 1/22/2012, the prediction was for a long, quiet series of solar cycles, following the 2013 maximum. Since our nation has already passed up years of opportunity to prepare for a solar flare disaster, and since it would take about 3 years to prepare if we'd started in 2013, there were only two meaningful things to be done.

1) Shut down all nuclear power plants (before a solar flare strikes).

2) An executive order which would establish a national emergency force and plan to provide for a year's worth of backup power. Under National Guard protection and execution, helicopter deliveries of stockpiled fuel, replacement diesel generators, and replacement operating and management personnel would be made available to all of our nuclear power plants, once it becomes apparent that blackouts are imminent.

Let's not face that choice again.

Key government and military officials must think about, and publicly discuss --how dangerous it is to continue operating our nuclear power plants --while our good luck holds.

Sources: John Kappenman of Storm Analysis Consultants and Metatech Corporation, as commissioned under Executive Order #13407, NASA Planetary Sciences Director James L. Green (See the February issue of Sky & Telescope), National Research Council Chair Daniel N. Baker (Space Physicist),

> http://www.21stcenturysciencetech.com/Articles_2011/Spring-2011/Power_Grid_Threat.pdf

> http://www.ibtimes.com/articles/194166/20110808/solar-storms-severe-solar-storms-earth-paralyse-carrington-event.htm

* Against all the above bad news about nuclear power plants, there's good news in that solar and wind power alternatives are coming on line with a kilowatt-hour operating cost that's significantly lower than nuclear power plants (aside from the inability to estimate the costs for disposal --since no such disposal site exists).

* Hopefully, the solar and wind industry will get away from the retail level co-generation of power, myriad complex demark/interfaces (since power must be reliably taken off when lines are damaged), loading home owner roofs with panels (fire and storm insurance is bound to become a real problem), locating noisy windmills near communities --and turn instead to distributed, professionally managed, renewable energy power plants.

* Retail energy storage (say: via electric car batteries) also strikes me as being hare-brained, hazardous and unreliable. I'm reminded of 1950s notions that homes of the future would be equipped with nuclear powered hot water heaters. Even professionally managed, large scale energy storage can be expected to present dangerous consequences, should something go amiss. I don't have answers here --except that alternatives to both nuclear and fossil fuel generated power must be found.

4/27/2018: Counterpunch has published an article by John Laforge assuring us that our impressions about the magnitude of the Fukushima disaster have not been based in hysteria. "Total atmospheric releases from Fukushima are estimated to be between 5.6 and 8.1 times that of Chernobyl, according to the 2013 World Nuclear Industry Status Report." Fukushima is the worst nuclear disaster in history.


About this web page and service:

* I started it by default of anyone else doing this work for my part of Oregon (which I found hard to believe). Until a new Radiation Network private station appeared in Florence in 2014, I remained the only entity, public or private, doing and posting regular monitoring along the Oregon coast.

* I no longer make much of an effort to popularize my own monitoring numbers --which (to date, and thankfully) have been steady and mild. I worry about giving people false assurances, and should my numbers go up, I'd worry about spreading false alarms. However, it would be wrong to stop keeping and posting this record --as long as my equipment holds up.

* Although I've been monitoring each day and watching the minute-by-minute log for spikes, my manually composed graphs over the first quarter of 2015 were no longer continuous --just representative --for an assortment of reasons: We stopped paying Charter Communications^ $55/mo for Internet access (something which once cost $10). Trundling down to our library for a short period of access meant higher priority Internet traffic came first. Also, I became discouraged. The CPMs barely change --which is good news, of course, but also: I didn't know what I was counting, and I couldn't get definitive answers.

* I created this Web page (thanks, NeoCities!) after the system at www.RadViews stopped loading my graphs. I've dedicated our old Dell laptop to Geiger counting/logging 24/7. Both the computer and the outside Geiger counter (a GMC-200) have battery back up, allowing reliable and continuous 24 hour averaging with minute-by-minute logging and spike alarming.

^ Even though the fine print cites "Charter Communications" on my latest Internet service offer, the big print is doing business as "Spectrum". The printed offer states that my "address" is "prequalified" to be connected for only $14.99/month, but an earlier such offer indicated that becomes about $20/month to include a WiFi router. (Our Chromebooks are WiFi only). When I asked about these offers at the local Spectrum office, one representative said we'd get "means tested" (which usually means there needs to be a young student or someone in the house on some type of assistance --which is not the case here), but the other implied we wouldn't. When I asked how long that price would last, his answer: "until there's a price increase".


Other Monitoring Services

* Sunshine Coast Computer Club, Inc.:
> http://sccc.org.au/archives/2630
Peter Daley's SCCC web site based monitoring, record keeping and public presentations are exemplary. More-over, he backs up his monitoring with the demanding work of gamma spectrometry on consistently captured and prepared samples. Peter maintains an extensive list of international radiation monitoring stations --at:
> http://sccc.org.au/wp-content/uploads/2016/07/International-Radiation-Monitoring-Station-List.pdf

* GQ's Geiger Counter World Map:
> http://www.gmcmap.com/

Last time I looked, GQ Electronics' World Map was displaying more than 100 stations across the United States, which had logged on and refreshed their reports during the previous 24 hours. (My outside station uses one of GQ's counters.) An advantage to this network is that most of its stations appear to use one of GQ's (affordable) counters, and (last I checked) those counters all use the same G-M tube/s. More-over: if you click on any of these stations, you get its long term average and its CPM history. (Nice going, GQE!) I've always found GQ responsive and they're considering my recent suggestion to automatically "equalize" these mapped stations by displaying their counts as percentages --of each station's average (next time they decide to overhaul/reprogram their system). Meanwhile, we need only click on any station in question to get that contextual information.

Like the other private networks on this list (to the best of my knowledge), there may be suggestions, but no hard rules as to station/shelter construction, locations and maintenance (as one would expect of a networked weather station). However: since GQ's G-M tubes mainly respond to gamma (and very hard beta) radiation, and since most residential construction is fairly transparent to gamma, station-to-station consistency is probably good enough. I'd certainly join this network if I were on-line here.

* EnviroReporter:
> http://www.enviroreporter.com/
There's very much to see at Michael Collins' EnviroReporter web site --and: you can easily get at all of the EPA-RadNet station graphs --in their original 9 channel format. See:
> https://www.enviroreporter.com/radnet-air-monitoring-data/

* Radiation Network:
> http://www.radiationnetwork.com/
> http://www.radiationnetwork.com/Message.htm

* At the "Message" link, Mineralab/Radiation Network owner Tim investigates and posts what I consider to be honest and rational reports about unusual readings across his network. (Yes: he has identified what appear to be actual radiation alerts.) Unfortunately, very few alerts are attended to with follow-ups. I understand that a comprehensive "Alert Log" is being developed for a future version of RN.

* Perhaps the strongest feature of RN is its "All Station Average" graph:

--which I'd much prefer to see as a single black line (hour averages, say) against a white ground.

* Radiation Network's stations report in "CPM": counts per minute, which makes a lot more sense than uSv/hr or uR/hr when the source is not known. Unfortunately, different Geiger counters have different sensitivities, which RN's map icons and legend attempts to take note of, by distinguishing between "high" and "normal" sensitivity instruments (thus: those two graphed lines/bands).

* For presentation on their public (Web page) map, the determination of individual station trends and "Alert" status is being averaged over intervals longer than a minute.

* Radiation Network's current "Alert Level" of 100 CPM was a good compromise choice, but later it was individually adjusted to accommodate the disparities among their monitoring stations.

* None of the stations are characterized as to what's being counted or how and where those instruments are positioned --but (again), high and normal (low) sensitivity stations are identified and their responses are being roughly equalized as to trend status. {2/9/2019: This web site is still functioning, but the "Alerts" seem dated. We're unable to access individual station radiation histories.}

* RadNet:
> http://www.epa.gov/radnet/radnet-data/index.html
Not to be confused with "Radiation Network", RadNet is the EPA's no-bid private contractor for keeping tabs on radiation blowing across the United States. It's performance and readiness over the years has been disappointing. Last I looked, RadNet's data was posted to the public as one-line (all gamma counts totaled) graphs. To get at the original 9 energy channel format, scroll down at EnviroReporter's web site. Seeing historical RadNet data (and current data in context) use to require an NETC membership, but I've recently (September 2020) seen a statement there that "everything is free".

* RadWatch (fka: The BRAWM Team)
   University of California's Berkeley Campus Air Monitoring:
> https://radwatch.berkeley.edu/airsampling
I've not checked this site recently, but they didn't seem to be up to speed in the past. I've been unable to reach them with questions. They were at one point doing great and professional work, monitoring milk, water and air filters, plus explaining the complexities of radiation science. {2/9/2019: I checked in today and this web site looks operational. They've added synchronized (rate of) rainfall, wind/direction and solar activity. I'll have to spend more time there and make a better report.}

* NETC:
> http://netc.com/
It's not clear to me how their "RadCon" levels are determined on their public map, so I tend not to pay them much mind --plus: it use to cost $20 per year for a paid subscription. However, on my most recent visit I saw the statement: "everything is free". Network owner Harlan has done an exemplary job of graphing years worth of RadNet's(!) and NETC's private stations --with your choice of averaging and time spans (wow!). The many stations on NETC's map/s are displayed with status symbols that are based on each station's long term average (yay!). NETC reaches into Japan as well. Here's an example of the NETC's graphs:


3 Years of (day averaged) beta data for San Bernardino, California (click to enlarge this image.)


* Black Cat Systems:
> http://www.blackcatsystems.com/RadMap/map.html
The main advantages of this private network are equalized monitoring stations which use Black Cat's excellent software and Geiger-Mueller tube sensing units. Black Cat posts no characterizations for its stations --no matter how high they might read. I see no station graphs.

* uRADMonitor
> https://www.uradmonitor.com/
--which is run by one Radu Motison. He apparently supplies DIY automatic reporting device kits which detect a variety of polluting factors (to judge from a recent promotional video). He's setting up a serious monitoring network. (I'm doubtful about DIY kit based networks, however. Standardization and quality control in equipment and methods are vital for reliable data.)

* Germany's Network:
> http://odlinfo.bfs.de/
> http://translate.google.com/translate?sl=auto&tl=en&js=n&prev=_t&hl=en&ie=UTF-8&u=http%3A%2F%2Fodlinfo.bfs.de%2F
(My outside station is affordably modeled on theirs. They've also responded to my questions.) {2/9/2019: I was unable to click on and get at any station histories, although that's nominally still in the offering.) (2/10/2019: Still no histories.)


My Choice of Geiger Counters and Radiation Units
(partially revised: 1/5/2017)

** Were I now just starting out to monitor local background radiation, I'd very likely purchase the GMC-320 version-4, produced by GQ Electronics. This affordable (currently: $118 via Amazon.com for the version-3), self-logging Geiger counter has a timed total count function (like the expensive counters: Gamma-Scout, Inspector, Mazur, etc). Both versions 3 and 4 permit outside monitoring (sealed up with desiccant in a "Ziploc" freezer bag and placed in a steep roofed "bird house" shelter) without having to bury cable to it, since you can periodically take it back into the house or office for a minute-by-minute debriefing to your computer --or simply to read its display for the day's timed count (say: 12 to 24 hours).

  ~ If you go this route, be sure to let the Ziploc bagged/packaged 320 (or any other such instrument) warm up to within 5 degrees of room temperature before opening it in the house. (The 320 displays its own internal temperature --nice!)

  ~ The 320 is a bit power hungry, so if you plan to leave it in the shelter for (say) a week at a time, replace its lithium battery with a good brand name lithium having a 2500mah capacity. (My current outside unit is a cabled GMC-200 --which uses the same G-M tube as the 320.) See here for more about my setup.)

* The earliest graphs on this page report Geiger counter ("GC") radiation measurements in terms of indicated "uR/hr" (micro-REMs per hour, which equals uSv/hr times 100) --"dose rate" units. The use of Geiger counter "REM" units (Roentgen equivalent man") is nearly always invalid since it's supposed to be about a hypothetical person's received bodily dose from a single, defined, external, isotope source. My Quarta-Radex and Medcom "Inspector" Geiger counters' REM calibrations can only be roughly correct for a cesium-137 source. For other types of radiation --like external alpha radiation (which doesn't even penetrate the skin), it becomes meaningless. In short: a (windowed) Geiger counter counts alpha, beta, weak and strong gamma as equal *clicks* --but they are not physiologically equal.

(The other radiation unit you'll encounter is the "gray"/"Gy", which is usually the same as the "sievert" for gamma radiation.)

* The alternative of simply using "CPM" (counts/clicks per minute) is far more rational and honest --but unfortunately, people are using many different GCs which report varying CPMs for the same kind and intensity of radiation. However, since most GCs have been factory calibrated to yield similar uR/hr or uSv/hr values for cesium-137 under similar circumstances --we can at least hope to get similar readings with respect to "background" radiation by using those "dose" units --especially if our radiation sources are largely gamma/photonic in nature.

* After buying a Medcom "Inspector" Geiger counter with CPM readouts (and alpha sensitivity), I began logging my readings as "counts", averaged to counts per minute, over long periods of time (usually: 10 to 100 minutes).

** However: for 2014 through to the present, I've been logging very long term averages (now about a 24 hour count each day) --as a percentage of my outside station's average for the first two weeks of 2014. I think that beats any other radiation unit --for integrity, station-to-station comparisons and for avoiding confusion.

** During the first hours of the Fukushima disaster, our government's and the Navy's estimates of radiation exposure were being logged and quoted with errors of up to 1000x, simply because they were not prepared to convert between the several units which are still in use: milli, micro and pico versions of REMs, Rads, Sieverts, Grays and a variety of CPM rates from various instruments --not always correctly deployed and read.

* That (the above) all having been said, and for better and worse: Europe's and Asia's government and private network's use of Sieverts (micro and pico), their accessibility and transparency (compared to the USA's horseshit, sweetheart contracted RadNet system), has pretty much set the Sievert as the standard radiation unit for us all. Some affordable Geiger counters only read and log in micro-Sieverts per hour.

* My average outside and inside office ambient (or "background") readings here are very similar and usually vary from about 8 to 12 "uR/hr", which averaged about 36cpm with the Medcom GC, but comes in close to 16cpm with the M4011 and SBM-20 Geiger-Mueller tubed units I'm now using. But I simply log it all as a percentage of my station's long term average.

The best policy is to -always- use Geiger counters in the same way and at the same monitoring stations.


My Geiger Counter's Failure

* The G-M tube (an LND-7317) in my Medcom "Inspector" Geiger counter failed. The unit still had high voltage which measured at an indicated 480 volts, using a 40 meg-ohm loading probe. (The unloaded voltage might well be the 500v that the 7317 is rated for.) I can only assume that the brief starting voltage (too brief to see w/o an O-scope?) is in the range of the specified 400v to 425v.

* The Inspector's electronics counted up when I brushed the isolated test probe across the G-M tube anode connection^.

^**^ Caution: Don't have the G-M tube in the circuit when you do this test! As little as 20pF (20 uuF) of external capacitance to circuit ground (like what's between the test leads from your meter), if placed directly across a G-M tube, can destroy it, so if the G-M tube is in the circuit,stand off your test probe with at least a 4.7 meg-ohm resistor at the tip. (I like to use the input resistance of the volt meter for the stand-off resistor --so I can simply double what's displayed. By knowing the combined DC probe impedance of your meter, and knowing the effective source impedance of the circuit you're probing, you can multiply the display voltage by whatever factor is required --should you need to know the unloaded voltage in a high impedance circuit.)

* Unimpressed by the life span of my pancake G-M tube (AND its original 90 day warranty via Medcom --extended to a full year in 2014), I replaced it with a Russian SBM-20, which can be had for about $35 (maybe $20 if ordered direct from an old Soviet country). These are tough, durable puppies with about 43% the gamma sensitivity of an LND-7317, no low energy beta sensitivity, and (of course) no alpha sensitivity at all.

* The operating voltage and the initial voltage had to be reduced to about 400 and 300 respectively. Consequently, I added a high resistance voltage divider consisting of five 10 megohm ("10M") resistors between the original G-M tube anode connection and circuit ground, then tapped off about 380 volts after the first 10M. That first 10M (R1) is bridged with a 15pf (15 uuf) disk capacitor (C1), so that the Inspector's electronics can feel the brief pulses. (Ctrl+ to enlarge this image.)

The following four 10M resistors (R2 through R5) are bridged with two 15pf capacitors (C2 and C5) in series, such that only 2/3rds of the initial supply voltage is felt by the SBM-20 tube.

* This modification resulted in a steady 2ma drain on the 9v battery (18 milliwatts) --for about 23 days of battery life, where I use to get about 3 months per battery. However, I no longer use this Geiger counter continuously. (Even though the divider string only accounts for only 4.2 milliwatts, one might consider doubling all of the resistors.)

It's my guess that this will degrade the high rate performance of the tube, but by using a pulse data cable connection to my PC, the high end already starts rolling off above 5000cpm anyway, and badly above 15,000cpm (compared to Inspector's internal rating as being good to 350,000cpm --with the original G-M tube, of course).

* With an SBM-20, the uR/hr display would of course be way off, but I've only ever used timed CPM totals (since the Inspector's sampling period is only 30 seconds or less for anything else).

* I operated my Medcom Inspector pretty much continuously for the first 14 months. In an average 36cpm background field of radiation, that works out to 22 million total counts (2.2 x 10^7), whereas the expected G-M tube life is quoted at from 10^9 to 5 x 10^10 total counts --so it failed about 100 years short of the mark.

* References:

> http://www.lndinc.com/products/17/

> http://www.gstube.com/data/2398/


My comments, questions --and drivel

* Radium and X-rays --the first radiation sources to be commercialized and medicalized before WW-1, were greeted with open arms, as was "atoms for peace" and nuclear power after WW-2. It's hard to believe how much radiation children were subjected to as a shoe sales gimmick (previous to 1960, via fluoroscopy: 16 to 75 REM/min to the feet, above 0.1 R/hr at a distance of ten feet from the front of the unit)--! Scores of young women ingested radium in the course of "pointing" the brushes they used to paint watch dials. There was a pottery factory in San Francisco which made radium laced water cooler/dispensers that they shipped nationwide. (I photographed an old one in Minnesota.) Stenciled on its side were instructions to drink several glasses of water from it each day for good health. The December 1915 issue of Scientific American cited a company which sold radium in the form of fertilizer, to be distributed at the rate of one pound per 50 square feet. That article faulted this product as being not nearly enough to make a difference, and that enough would simply be too costly. With a half-life of 1590 years, remnants of these products, especially at old warehouse and factory locations, must remain a hazard.

* While all radiation carries an estimable hazard (per:
> https://www.freespeech.org/video/theres-no-such-thing-safe-level-radiation
--so do things like getting out of bed in the morning, breathing city air, driving a car, etc. --all of which a rational, caring person (especially a parent) attempts to minimize. Possibly it's the case that a healthy person's body is usually able to repair the damage (at a cellular level) --for the prevailing rates of "background" radiation --at least in one's ancestral home. Whether or not that's the case, the hazards of external radiation can at least be rationally compared to every-day exposures --natural (like the radiation from potassium 40 in your own body) and artificial (like disturbing the ground for your home's foundation), which seem largely unavoidable in modern life.

That having been said: you especially want to minimize eating/drinking, breathing in or somehow wearing a radioactive substance. You also want to avoid counsel from anyone who proposes to compare ingesting radioactive substances to chest X-rays, sunshine, air travel, or eating bananas.

See the preamble to this page for my latest take on what the heck it is I think I'm counting.

* Our society needs supportive feedbacks at all levels, but does not have a method certain for earnest amateurs (once upon a time encouraged with the title: "citizen scientists") --to get competent counseling.

    ~ This is a much broader issue in that many amateur interest groups (concerned with [say] UFOs, contrails, fluoridation, vaccines, 911 and other issues/conspiracies) --find themselves isolated and left to their own --perhaps self-defeating-- devices, methods and assumptions. These factions then drift further apart from the "main stream" and from each other.

Be my guess: this is due to that familiar "high school popularity contest effect". The competent professional (usually educated at great public expense) can not personally afford to engage such people (the public), lest s/he suffer the "de classe" effects of being tainted by association with the "great unwashed" or "the wrong sort", or get stupidly quoted out of context, or perhaps flat out misquoted --thus ending up with less credibility among and traction with his/her colleagues --on that slippery upward slope toward a successful career. The integrity, coherency, mutual respect and trust of our society suffers as a consequence.

* As to the integrity of traditional handheld Geiger counters, I can answer that one. Despite recent versions being explicitly designed and sold for background radiation monitoring, their original purpose was for use as survey instruments --to help clean up a messy lab, to be deployed during an accident or an attack involving radioactive materials. Typically, they're calibrated at a level of 1000 uR of cesium-137 radiation --100 times above my average background levels.

That be as it may, we use them in our monitoring work because they're affordable ($100 to $1000).

* At first I thought that my Geiger counter background/baseline readings were mostly about "NORM" --naturally occurring radioactive material/isotopes in the ground, beach sands and in the air --plus any fall-out from the events in Fukushima Japan or elsewhere. (I use to supplement my fixed station readings with remote beach station readings and occasional one-shot air filter readings, plus outsourced gamma spectrometry for suspicious filters.)

* Then I became persuaded that I'd been largely counting "muons" --those secondaries which reach the Earth, generated by the steady rain of cosmic primary rays, but Robert Hart (see:
>http://www.hardhack.org.au/cosmic_ray_telescope
--and others suggested that the muon component (at sea level) amounts to 10% or less of even a low background count.

* As of July, 2016, it appears that about half of a count at low "background" levels (say: 10 uR/hr) is cosmogenic plus a minority of internal G-M tube noise. (It's tough to discern the difference. A coincidence detection setup should help.)

* On 5/25/2016 I submerged my mobile Geiger counter to a depth of 2 meters --off the end of a dock on our salt water bay (using an old army ammo box for a pressure vessel).

I followed that up with another 30 minute run with the box suspended just above and touching the water's surface. That resulted is a significantly reduced count (to about 65% of what would normally be expected --a meter off the beach) (which I verified the next day: see run "run g").

My earlier submersion tests had cut the counts roughly in half.

* Previous shielded tests indicated an irreducible minimum in the range of 75%. Another test run on 5/30/2016 (lead shielding only) indicated a 72% remainder (of noise/whatever).

  ~ *Click here* to see my data and supportive particulars. Perhaps you can draw more informed conclusions.

* Adding to the confusion is that Tom "Anti-Proton" (nom-de-Net) has repeatedly passed through medium altitude null zones of close to zero Geiger counts --when taking his Geiger counters and a compact scintillator/gamma spectrometry setup along on his many business related airline flights. (I believe that Tom is too well informed/experienced and equipped --to have been fooled by sensor overload.)

* A Geiger counter's own internal noise might be sourced from the G-M tube or other materials in the Geiger counter.  --Those counts, of course, would not have been reduced by submersion --or truly effective shielding.

You might find it dismaying to check the noise specifications for your Geiger counter and/or its G-M tube, which is variously listed as "self", "own", "inherent" or "maximum shielded background". (They don't seem to like the term "noise".)

The noise in some G-M tubes is rated in "CPS": counts per second. For instance: the big Russian "SBM-19" G-M tube's specifications indicate an "inherent counter background" of 1.83 pulses per second --which would be a whopping 110cpm (--SHEESH!). My outside station's G-M tube (an M4011) lists noise at 76% of my long term average --and a drop to 75% is what I got by packing an SBM-20 tubed counter of mine in 40 pounds of lead shot. (Lead shot is a poor substitute for the good stuff used in a gamma spectrometry lab, but it's cheap, widely available and it packs well.)

* Straight away, I hope you can see the consequence. Let's say your averages go up from 35cpm to 40cpm. That might not be a 14% increase in what we're worrying about (Fukushima or domestically sourced radioactive contamination). It might actually be a 250% increase --right?-- but after an atmospheric or oceanic plume of radioactivity arrives, perhaps it won't look like much of a change in a Geiger counter's total counts (noise + muons/whatever + an actual on/in the ground increase). (As of July, 2016, I'm assuming that most "noise" is due to cosmogenic radiation, and that all noise makes up about half of a count at an indicated "10 uR/hr".)

2/9/2019: To anyone marketing radiation monitoring equipment, software and networking.

Suggestions:

* Try to keep the station keepers' network simple and free of meaningless "noise" by using sealed (from dust/particles) outdoor housings plus moderate beta and alpha shielding as a default station configuration. Everyone's automatic reportage should be mostly a gamma count.

* In order to log any environmental beta and alpha, offer sampling equipment and simple but methodical procedures for doing so --especially standard air filters (cut to fit N95 material), PVC holders and a small (affordable to purchase and ship), known air flow, network system standard, cannister vacuum cleaner unit.

* All stations should be logging (and/or via their software) on the same UTC, 24 hour time line.

* All stations should be reporting counts as a percentage of their station's base line average (say: the first two weeks of operation). Existing stations should be encouraged or automatically required (via default software settings) to do another base line, all at the same time of the year.

* Software generated network graphs should all be for the same UTC periods (24 hours, week-long, etc.). While day graphs might show unembellished, super-imposed lines for 1 minute, 10 minute and hour long counts (like my modified Mineral Lab "GeigerGraph" system graphs), week-long graphs might be only hourly counts, month and/or year-long graphs would show day averages.

* When the public accesses a national map of participating stations, clicking on any one of them should bring up at least a graph of day averages (gamma only/mainly) for the past 7 days, and preferably, for the past 30 days --similar to the German network.

6/16/2015: * That 6/9 peak extended into the 2nd day with what looks something like a decay curve. I've seen no such readings elsewhere, so I'm still guessing it was a neighbor's bout with "nuclear medicine", but using something other than technetium-99m.

6/8/2015: Have begun watching for (and noting) 10 minute averaged periods which reach or exceed 4.4 standard deviations (21cpm), per my copy of a GeigerGraph beta program. It may be (and has already been) that highs occur without an accompanying 1 minute count peak (of any special note) --and vice-versa.

5/25/2015b: I've discontinued my 30 minute remote (beach and bay) station counts in favor of beach "wanders".

* The difficulty of getting qualified comments about radiation issues is disappointing. I'm old enough to remember a readiness among the academically/professionally qualified to encourage earnest amateur pursuits and the "citizen scientist". Of course there use to be more willingness to uncritically accept authoritative answers, and now there's the Internet. I imagine that professionals are apprehensive about being blaringly misquoted out of context, held up to ignorant ridicule, becoming suspect of indiscretions with "privileged information", and simply being widely seen to be consorting with the academically unwashed.

5/24/2015: * I reached back and added a percentage range to all the program generated graphs --which made for an interesting review. At some point --shortly after my Medcom Inspector Geiger counter failed, and maybe about the time I broke my leg, I seem to have gotten about 1cpm out of calibration, as I transitioned through my 2nd and then to a 3rd Geiger counter. The graphs themselves, however, evidence what the equivalency should be, so that's what I've gone by. (Tentatively: I'm claiming that my new SBM-20 G-M tube "matured" into a bit more sensitivity.)